where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Canadian Institute for NDE
We are specialized in training for Radiography, Ultrasonics, Magnetic Particle, Liquid Penetrant, Eddy Current and emerging NDT technologies.
1840 views
Technical Discussions
Mr Burton
Mr Burton
03:50 Mar-17-2010
Pipe thickness and pitting

I would like to seek information about measuring wall thickness and pitting for a 350mm diameter, 20mm wall thickness, probably about 12mm now in places. Used for iron ore slurry.

 
 Reply 
 
Jon Wallis
NDT Inspector, -
Netherlands, Joined Feb 2010, 626

Jon Wallis

NDT Inspector, -
Netherlands,
Joined Feb 2010
626
09:23 Mar-17-2010
Re: Pipe thickness and pitting
In Reply to Mr Burton at 03:50 Mar-17-2010 (Opening).

The first line of attack would be ultrasonic wall thickness measurement. To carry out wall thickness measurements with ultrasonics the pipe would have to be comfortably accessible and 'bare metal' i.e. free of coating, insulation, rust etc. Typically, measurements can be made - assuming we are talking of carbon steel - with an accuracy of 0,2 mm or so in the field. Oviously an asessment of the situation on site would be required.

If the line is insulated, an alternative method of measurement, without removing the insulation, might be Incotest. Incotest is a stand-off measurement system which can 'look' through insulation and assess the remaining wall thickness compared to one point where the insulation has been removed and a comparision is made.

You mention pitting. I wonder, considering the medium in the line (iron ore slurry), if there really is a problem with pitting. I tend to think that the problem would be erosion. However, if pitting is present and this is local loss of wall thickness rather than needle pitting, this should be possible to detect.

Needle pitting, which is usually a problem with exotic steel sorts, is very difficult to detect with either of the above methods (read impossible). Radiography may work.

 
 Reply 
 
Aaron Greenbank
Sales
Innospection, United Kingdom, Joined Jan 2010, 1

Aaron Greenbank

Sales
Innospection,
United Kingdom,
Joined Jan 2010
1
10:33 Mar-17-2010
Re: Pipe thickness and pitting
In Reply to Mr Burton at 03:50 Mar-17-2010 (Opening).

Dear Sir,

Another method that you may wish to consider is SLOFEC, this is an eddy current based technique which uses magnetic saturation to aid the induction of eddy currents into the specimen. This is an excellen tmethod for fast screening for corrosion typical of what you have described.

 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
13:59 Mar-17-2010
Re: Pipe thickness and pitting
In Reply to Mr Burton at 03:50 Mar-17-2010 (Opening).

We have a general application note on ultrasonic corrosion gaging that may be of interest if you're new to the subject:

http://www.olympus-ims.com/en/ndt-application/183-id.209715222.html

 
 Reply 
 
Rich Roberts
Engineering, Executive Managment
Quest Integrity Group, USA, Joined Nov 1998, 78

Rich Roberts

Engineering, Executive Managment
Quest Integrity Group,
USA,
Joined Nov 1998
78
14:11 Mar-17-2010
Re: Pipe thickness and pitting
In Reply to Mr Burton at 03:50 Mar-17-2010 (Opening).

You may want to consider applying an Ultrasonic (UT) based Intellingent Pig technology. Even if the line is not designed to be inspected by way of intelligent pigs, there are pigs which are capable of running in these lines. Some Ultrasonic based intelligent pigs will provide +100% overlapping coverage to ensure the entire surface is inspected. Detecting and quantifying Corrosion, Pitting, Erosion along with any deformation (i.e. Denting, Ovality, Bulging, etc.) can be accomplished with one pass of the intelligent pig tool.

 
 Reply 
 
Jim Kovarik
Engineering
Lixi, Inc., USA, Joined Nov 1998, 39

Jim Kovarik

Engineering
Lixi, Inc.,
USA,
Joined Nov 1998
39
17:08 Mar-18-2010
Re: Pipe thickness and pitting
In Reply to Mr Burton at 03:50 Mar-17-2010 (Opening).

You may also want to consider the Lixi Profiler if the line will be or can be evacuated.

 
 Reply 
 
Zach McCann
Zach McCann
08:50 Mar-31-2010
Re: Pipe thickness and pitting
In Reply to Mr Burton at 03:50 Mar-17-2010 (Opening).

Hello Mr Burton following on from the information Aaron sent you I represent Innospection here in Australia. I would be happy to discuss this if you woudl care to drop me an e-mail.

 
 Reply 
 

Product Spotlight

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window