where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

518 views
Technical Discussions
Ahmed M.Eid
Ahmed M.Eid
04:35 Sep-23-1998
Ultrasonic

Dear prof.;

I'm assistant researcher in ultrasonic Department ( National Institute of Standards) in Cairo, (Egypt). I have M.Sc. in solid state physics from Cairo University. I prepare for my Ph.D. in field of composite materials properties using ultrasonic methods.
The available equipment is Flaw detector, normal & angle probes, Immersion tank, wave generator, Impedance analyzer and reference blocks.
The question is what kinds of composites I can study?

Thank you in advance

Sincerely,
A.M.Eid




    
 
 
Yoseph Bar-Cohen
R & D,
Jet Propulsion Lab (JPL), USA, Joined Nov 1998, 26

Yoseph Bar-Cohen

R & D,
Jet Propulsion Lab (JPL),
USA,
Joined Nov 1998
26
05:40 Sep-24-1998
Re: Ultrasonic
: Dear prof.;

: I'm assistant researcher in ultrasonic Department ( National Institute of Standards) in Cairo, (Egypt). I have M.Sc. in solid state physics from Cairo University. I prepare for my Ph.D. in field of composite materials properties using ultrasonic methods.
: The available equipment is Flaw detector, normal & angle probes, Immersion tank, wave generator, Impedance analyzer and reference blocks.
: The question is what kinds of composites I can study?

: Thank you in advance

: Sincerely,
: A.M.Eid
:

Dear Mr. Eid,

With the hardware that you have you should be able to study wave propagation through
composite materials such as graphite/epoxy. If you would like to make a scientific
contribution to the field of NDE, you may want to conduct a literature search to see
what was already done in this field. As you can imagine, there has been a lot of
research studies that were conducted with ultrasonic wave propagation in composite materials.
However, the complexity of the issue always leaving room for new ideas and problems to tackle.
Particularly, I believe that the issue of polar backscattering from composites is still not completely
understood. Also, it will be nice to find a wave to measure the density of composites with
access from a single side without involving the effect of the wave velocity. We need a reliable method
of measuring residual stresses.

Yosi



    
 
 

Product Spotlight

TVC awarded UKAS accreditation

TVC are delighted to finally announce we have been awarded UKAS accreditation for our calibration
...
laboratory. Laboratory accreditation to ISO/IEC 17025:2005 enables us to conduct the Electrical Verification of Ultrasonic Flaw Detection Equipment to BS EN 12668-1:2010. It has taken many months of hard work and we want to thank our staff for all their efforts during this massive undertaking.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

PROlineTOP Plug & Play Ultrasonic inspection device

As Plug & Play solution it units all control and operation elements in a small housing and therefo
...
re replaces the typical control cabinet...
>

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window