where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

618 views
Technical Discussions
kcc
Student
Malaysia, Joined Oct 2001, 3

kcc

Student
Malaysia,
Joined Oct 2001
3
04:46 Oct-25-2001
wavelet toolbox in matlab

hi! Do anyone used to perform any continuous wavelet transform by using matlab?I need some knowledge about doing this job!!

thanks!!


 
 Reply 
 
Henry Herrera
R & D,
UT Quality, Canada, Joined Jun 2000, 19

Henry Herrera

R & D,
UT Quality,
Canada,
Joined Jun 2000
19
02:34 Nov-04-2001
Re: wavelet toolbox in matlab
MatLab Toolbox has any function that you need for your work with wavelet.
But which version of Matlab do you have?
And what are you looking for? Noise suppression, echo detection?
You can send me the signals.
Also I'm using the Jens Forker's program (AGU Vallen Wavelet) and in most cases it works very good.

Best Regards.

Henry
_______
M Sc. Eng.
Associate Researcher.
R&D Group. NDT Lab. Cuba.
E-mail: henry@aconci.perla.inf.cu
hentronix@hotmail.com


: hi! Do anyone used to perform any continuous wavelet transform by using matlab?I need some knowledge about doing this job!!
.
: thanks!!
.



 
 Reply 
 
zhao
zhao
01:14 Dec-02-2001
ocean profile
hi! Do anyone has the program to draw
ocean profile e.g. temperature-depth profile£¿
The plot axes should be in the top/left format.

thanks!!



 
 Reply 
 

Product Spotlight

ISONIC 3510

Very Powerful Superior Performance Extremely Portable Smart Phased Array Ultrasonic Flaw Detector an
...
d Recorder with 2 Conventional UT and TOFD Channels uniquely combines PA, single- and multi-channel conventional UT, and TOFD modalities providing 100% raw data recording and imaging. Suitable for all kinds of every-day ultrasonic inspections
>

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window