where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Teletest
Teletest Focus+ was the first system to use long-range guided wave ultrasonic testing to detect corrosion in pipelines.
426 views
Technical Discussions
AxlZ AekZ
R & D
King mongkut's university of technology Thonburi, Thailand, Joined Jun 2001, 16

AxlZ AekZ

R & D
King mongkut's university of technology Thonburi,
Thailand,
Joined Jun 2001
16
02:02 Nov-08-2001
Can I make coils sensor to use in wire rope inspection system?

If I want to detect localized faults by using coils sensor, Can I make them?
I want to know about
1. No. of coil (swg.)
2. core for coil(material)
3. No. of turns
4. directional
5. the important factors
6. flux density to saturate the rope (d=<50mm)
If can't tell me please guild line for me please.


Thank you very much.
AxlZ AekZ.



 
 Reply 
 
David Hermanutz
Consultant,
Hbndt.com, China, Joined Jul 2012, 85

David Hermanutz

Consultant,
Hbndt.com,
China,
Joined Jul 2012
85
07:13 Dec-12-2001
Re: Can I make coils sensor to use in wire rope inspection system?
: If I want to detect localized faults by using coils sensor, Can I make them?
: I want to know about
: 1. No. of coil (swg.)
: 2. core for coil(material)
: 3. No. of turns
: 4. directional
: 5. the important factors
: 6. flux density to saturate the rope (d=<50mm)
: If can't tell me please guild line for me please.
.
:
: Thank you very much.
: AxlZ AekZ.
.

Hi,

Please contact the man below who seems to invent the best wire rope equipment on the market.

http://www.ndt.net/article/v04n08/zawada/zawada.htm

Kazimierz Zawada
Zawada NDT, Tatarkiewicza 8, 41-819 Zabrze, Poland
Email: zawada@silesia.top.pl Fax: ++48 32 2752167 http://www.zawada.z.pl




 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

NEW! The PragmaPro Instrument Platform

The PragmaPro is based on a modular cartridge technology and supports various NDT instrument modal
...
ities such as UT, PAUT, ECT and many more. This new platform is based on a machined, powder-coated aluminum frame for shock-proofness, best sealing qualities and maximum heat dissipation. This is practical to extend the outdoor temperature range and/or to extend the power injected in the transducers. The PragmaPro is aiming at a very wide range of applications, such as weld scanning, corrosion mapping and composite testing.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window