where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

TecScan Systems
We offer a complete line of NDT scanners, Immersion Tanks & Gantry systems which incorporate Ultrasonic, Phased Array & Eddy Current technologies.
3966 views
Technical Discussions
pratchaya kittisakkul
pratchaya kittisakkul
20:03 Oct-15-2009
Aircraft Fiberglass Radome

I want to know about the best way to inspect delamination of a 10 mm thickness,Aircraft Radome made of fiberglass.At first I did 10 MHz and 15 MHz UT but It had many noises and so hard to see BWE.
Please let me know if you have any methods or UT technics that useful to inspect this fiberglass radome.

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 850

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
850
20:35 Oct-15-2009
Re: Aircraft Fiberglass Radome
In Reply to pratchaya kittisakkul at 20:03 Oct-15-2009 (Opening).

Pratchaya,

I think you maybe going the wrong way. I did some delam and disbound check on F18 and we would normally a 2.25 MHz transducer in a pitch an catch method. So I recommend lowering your frequency.

 
 Reply 
 
pratchaya kittisakkul
pratchaya kittisakkul
20:50 Oct-15-2009
Re: Aircraft Fiberglass Radome
In Reply to Michel Couture at 20:35 Oct-15-2009 .

Thank you michel I'm very appreciate your reply and I will try as you recommend.

If anyone have any technics to do with fiberglass radome,please don't hestitation to let me know.I still looking forward to any answers.

 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
22:48 Oct-15-2009
Re: Aircraft Fiberglass Radome
In Reply to pratchaya kittisakkul at 20:50 Oct-15-2009 .

I agree with M. Couture. We would normally recommend a 2.25 MHz test frequency as a starting point when testing 10 mm of fiberglass. Also, if your flaw detector has adjustable filtering, you should experiment with low pass filter settings to help clean up some of the scatter noise.

 
 Reply 
 
john harbert
john harbert
01:03 Oct-16-2009
Re: Aircraft Fiberglass Radome
In Reply to Tom Nelligan at 22:48 Oct-15-2009 .

typically i would think that you would want to use a thru-transmission method to find lamination/de-lamination in a composite part.
You should be using a procedure that gives step by step instructions for aircraft parts including the type of inspection to be used, and type of inspection equip to be used including transducers, couplant ...etc.

 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 303

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
303
08:38 Oct-16-2009
Re: Aircraft Fiberglass Radome
In Reply to john harbert at 01:03 Oct-16-2009 .

Hi Pratchaya,
I agree with John Harbert on this that Through transmission is best. I would also recommend trying to do it with C-Scan rather than just a probe each side, as this is too subjective.
2.5MHz seems a good frequency to start with, but if you are using C-Scan, don't be afraid to go down to 1MHz as well.

I assume the Radome has quite a curvature on it, so that will make it difficult to inspect, but we use automated and programmable machines here, working in through transmission C-Scan, so it really is a job for someone with specialist equipment.

 
 Reply 
 
pratchaya kittisakkul
pratchaya kittisakkul
11:48 Oct-16-2009
Re: Aircraft Fiberglass Radome
In Reply to Godfrey Hands at 08:38 Oct-16-2009 .

Thank you for every opinions.I will try to do technics that you all replies.Anyway,I would like to listen anyother way or your experience with this subject.
One thing I would like to know is about inspecting this subject with Advance NDT like Laser shearography or Thermal/Infrared or other methods to do with Aircraft fiberglass.

 
 Reply 
 
Simon Amallraja
Simon Amallraja
18:21 Oct-16-2009
Re: Aircraft Fiberglass Radome
In Reply to pratchaya kittisakkul at 20:03 Oct-15-2009 (Opening).

You can try Non Contact Ultrasound method. check with www.ultrangroup.com. you will get more details.

You can also try Rotary UT Phased Array method. check with www.sonatest.com for Rapidscan applications. you will find more details.

Simon

 
 Reply 
 
Jack A. R.
Jack A. R.
09:11 Oct-20-2009
Re: Aircraft Fiberglass Radome
In Reply to Simon Amallraja at 18:21 Oct-16-2009 .

Hi Guys,

Thanks for allowing me to make some suggestion here in this forum. This is a friendly advice, I would better suggest if you'll try radiography method (x-ray), I believe in every aircraft there's a MRP/MRO (Maintenance Repair Procedure/Operation). If these aircraft made by Boeing or Airbus they have their own procedure for NDT inspection of radome, so you don't need to worry just follow their procedure. Since the material is made of possibly (kevlar) fiberglass you can ask the owner of the aircraft for this requirements or manual. In aircraft industry always follow the manufacturer approved procedure (NDI) that's the golden rule, but if you're experimenting in your own and try and try until you succeed it's a long process. Hope this will give you other solution to your problem.

 
 Reply 
 
yoram shohat
yoram shohat
14:45 Aug-26-2010
Re: Aircraft Fiberglass Radome
In Reply to Jack A. R. at 09:11 Oct-20-2009 .

Please , I want to know the MIL-STD or ASTM for ULTRASONIC INSPECTION of composite laminates RADOME . The radome contain also Honrycomb.

Regards
yoram

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 850

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
850
03:24 Aug-27-2010
Re: Aircraft Fiberglass Radome
In Reply to yoram shohat at 14:45 Aug-26-2010 .

Yoham,

Instead of looking for a MIL-STD or an ASTM procedure, I recommend contacting the aircraft manufacturer. When dealing with NDT of aircraft, the manufacturer will normally publish an NDT manual containing all of the approuved procedures. I don't know about the laws of your country, but to inspect an aircraft by any other method and unapporuved procedures would get you in hot water with the FAA if you were in North America.

On my days on aircraft, one instrument we used for such work was the Bondtester. Very simple to use and fairly accurate.

 
 Reply 
 
Paul Sacker
Paul Sacker
11:37 Nov-04-2010
Re: Aircraft Fiberglass Radome
In Reply to Michel Couture at 03:24 Aug-27-2010 .

This can also be done as mentioned above using Thermal Imaging techniques - Both Boeing and Airbus have procedures for using Thermal Imaging to inspect composite structures. The technique is a variation of Flash or Lock-in Thermography. Have a look at the Thermal Wave website (www.http://thermalwave.com), or the AT Automation website (http://www.automationtechnology.de/cms/en/thermography.html) for a review of the principles.

 
 Reply 
 
Simon Amallraja
Simon Amallraja
14:41 Nov-04-2010
Re: Aircraft Fiberglass Radome
In Reply to Michel Couture at 03:24 Aug-27-2010 .

You have use very low frequency probes fior this application. Look at Sonatest website for Dryscan 410D equipment - you will have many details for your application.

Also look at Rapidscan 2 and 3D System from the same manufacturer. You will get more info.

Look into www.ultrangroup.com. Their Non Contact UT Systems will guide you more on your application.

Look at www.vidisco.com. Their fox rayzor - flat panel system will guide you more on your application

Look at www.zetec.com. Thier MIZ 21SR will guide you more on your application.

There are many manufacturers in the World for the above methods. I have mentioned which I am familiar with.

Good Luck

Simon

 
 Reply 
 
Alex Easton
Alex Easton
18:03 Nov-04-2010
Re: Aircraft Fiberglass Radome
In Reply to pratchaya kittisakkul at 20:03 Oct-15-2009 (Opening).

Hello Pratchaya,

The best way to inspect a radome for delamination is a simple tap test. Layout a grid on the external and internal surface and manually tap it out. You could set up an elaborate UT system with procedures, techniques and calibration standards if that suits you, but the tap test is the fasted, easiest and cheapest way to do it.

We have used bond testing systems and found that the tap test outperforms in all areas of the inspection; fast, easy, cheap, reliable and repeatable.

Don't forget to inspect for moisture. If it has impact delamination there is a very good chance for moisture ingress. Moisture has to be removed for transmission testing and structural soundness due to freeze and thaw in the flight cycle.

Most SRM's have this info. Request the information from the customer.

Contact me if you would like details.

 
 Reply 
 
Mike Nash
Mike Nash
21:10 Nov-05-2010
Re: Aircraft Fiberglass Radome
In Reply to Alex Easton at 18:03 Nov-04-2010 .

It seems that you pretty much have the answer already. However, next week I will try to ask a colleague of mine that works in aircraft restoration and is also a very experienced NDT practitioner.

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 850

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
850
03:11 Nov-06-2010
Re: Aircraft Fiberglass Radome
In Reply to Mike Nash at 21:10 Nov-05-2010 .

Some techs used to do that too when I was in the air force. The trick here is to have your quarter ($0.25) calibrated to be able to find the edge of the delamination.

 
 Reply 
 

Product Spotlight

MIZ®-21C: Truly Affordable Eddy Current Handheld with Surface Array Capability

Introducing MIZ-21C, the first truly affordable handheld eddy current instrument with surface array
...
capabilities. MIZ-21C can deliver fast, accurate inspections in demanding NDT applications including aerospace, oil and gas, manufacturing, and power generation. The surface array solution can reduce inspection time by up to 95% compared to traditional handheld pencil probes. The ergonomic design, long battery life, and intuitive touchscreen mean you can inspect more areas faster than ever without fatigue.
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

NovaScope 6000

The all-digital Novascope 6000 is a portable, ultra-high precision thickness gauge for high-speed
...
thickness measurement. Novascope 6000 has unmatched capabilities and unique features including: •Superior Resolution with high contrast, high-speed color RF display •High pulser voltage •Real-time video output •Increased internal/external data storage •Programmable SetUp features •Battery & AC Powered
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window