where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Phoenix Inspection Systems Limited
Design and manufacture ultrasonic Transducers, Scanners and Custom Solutions for NDT inspections. Innovators in NDT technology
2326 views
Technical Discussions
sadek997
NDT Inspector,
AR, Poland, Joined Feb 2011, 12

sadek997

NDT Inspector,
AR,
Poland,
Joined Feb 2011
12
20:43 Apr-05-2011
C3 radiographic film acc. to EN 584-1

As many radiographers know the EN 584-1 standard distinguishes few radiographic film classes. Of coure film manufacturers have comply to the specification of the standard and thare can be several ways to obtain the C3 film class. In our laboratory we use Fuji IX 80 films and the manufacturer states that the film obtains C3 class if the development temperature is 26 deg C. If the temperature equals 28 deg C the film class is C4 ass to EN 584-1. There are some dificulties in getting the appropriate sensivity (it's hard to get the appropriate wire of the IQI - usually one is missing). We've tryied many solutions with other parameters of the examination i.e. voltage, time, screens, distance and many other...

The question apperas are we using the right film type? (of course it is C3 according to the producer). Maybe it would be advisable to change the film manufacturer to e.g. AGFA and this way the sensivity would increase? I don't state that the IQI wire is impossible to obtain on this film system (film and developer) but it usually is quite a hard task. Maybe You had the same problem and it has vanished after changing the film manufacturer?

We use IX80 Fuji films packed in a ruber cassette with 0,05mm front screen and 0,1mm rear lead screens

 
 Reply 
 
GOWRISANTHOSH PALIKA
NDT Inspector,
Royscan engineering pte ltd, Singapore, Joined May 2008, 52

GOWRISANTHOSH PALIKA

NDT Inspector,
Royscan engineering pte ltd,
Singapore,
Joined May 2008
52
03:36 Dec-16-2016
Re: C3 radiographic film acc. to EN 584-1
In Reply to sadek997 at 20:43 Apr-05-2011 (Opening).

hi
to get better sensitivity the recommended front lead screen 0.1mm to 0.2 mm in the range

 
 Reply 
 
Dr. Uwe Zscherpel
Director,
BAM Berlin, Germany, Joined Jan 2010, 82

Dr. Uwe Zscherpel

Director,
BAM Berlin,
Germany,
Joined Jan 2010
82
11:13 Dec-20-2016
Re: C3 radiographic film acc. to EN 584-1
In Reply to sadek997 at 20:43 Apr-05-2011 (Opening).

Dear Sadek,
we at BAM are doing NDT film system classifiction and certification for differerent film manufacturers. Fujifilm does not have BAM certificates. Our measurements showed since many years, that the Fujifilm IX 50 in standard NDT development conditiions (28 °C and 8 min cycle time) is in the C3 film system class and IX 80 is in the C4 system class. Of course, you can find development conditions (e.g. the weak Japanese Fujifilm Superdol developer at 25 °C and 11 min cycle time) which require longer X-ray exposure times to reach D=2. As a consequence, the IX80 film just imps in tyhe next class C3! But this are NOT the con ditions you find typically in Europe.
So, if you are searching for a C3 film system class I strongly recommend to use the Fujifilm IX50 type. Than you will also prevent any problems with the wire visibility, which should be very similar to AGFA D4 films.
If you are using X-rays for exposure, the lead screen thicknesses are sufficient, if you are using Ir-192 the suggested increased lead thicknesses should give better IQI visibilities.
Finally, are you aware that since 2012 EN 584 is no longer valid and replaced by ISO 11699?
Best regards
Uwe Z.

 
 Reply 
 

Product Spotlight

Ultrasonic tomograph for imaging of concrete structures А1040 MIRA

Applicable for concrete inspection allowing imaging of the internal structure of objects from conc
...
rete, reinforced concrete, different stones. The operation applies pulse-echo technique at one-side access to the object. The instrument is feasible for concrete inspection for searching conduct ducts, conduits, detection of foreign inclusions, holes, honeycombing, cracks and other concrete defects.
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Varex Imaging Large Field of View (FOV) Digital Detector Arrays (DDAs)

A larger FOV DDA can reduce the space and volume of the X-ray inspection system on the factory floor
...
, enable faster scanning times, better throughput and better resolution images at a lower dose. Customers can also save time and money. With these benefits in mind, Varex Imaging has designed a family of large FOV detectors (4343HE, XRD 1611, 4343DX-I, 4343CT) for our industrial imaging customers.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window