where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

PBP Optel sp. z o.o.
Weare searching new ways - in ultrasonic techniques- in creation of new productsUltrasonic instruments - Ultrasonic Testing Card
1996 views
Technical Discussions
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1282

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1282
03:39 Jan-19-2004
ISO 13847:2000 Porosity and UT

I have just purchased my copy of the ISO standards 13847 Petroleum and natural gas industries - Pipeline transportation systems-Welding of pipelines.
The NDT requirements for testing are reasonably typical and I have no issues with them. However, the ultrasonic acceptance criteria for workmanship has a statement that for nonplanar indications which cover a projected area of not more than 2% on the radiograph shall be considered acceptable. (But this is in the Ultrasonic Acceptance Criteria Section 9.5 and there is no radiograph!)
It also allows that porosity indications may be treated as planar.

This does not seem very helpful to an ultrasonic technician.
It implies that ultrasonic assessment is to be made look like radiography. Although porosity and slag may be evaluated as planar the connection to a 2% projected area has little to do with ultrasonic assessment. (I have also noted that 2% projected area is rarely quantifiable even by experienced radiographers).

How did the ISO committeerationalise this kind of wording for ultrasonic testing? There is a contact in Geneva for problems with the file format but there is no instructions on who to contact when there is a techncal issue like making ultrasonic result equate to radiography.

Does anyone have a suggestion or contact route?
Regards
Ed



 
 Reply 
 
Sasaki
Sasaki
01:28 Jan-20-2004
Re: ISO 13847:2000 Porosity and UT
I wonder if this could be helpful, but please see

http://www.iso.ch/iso/en/xsite/contact/contact.html

My personal guess to your posting is that the stipulation of radiograph is made in case of dispute regarding interpretation of UT echo signal with regard to sizing the flaw.
That means, final interpretation should be made by radiograph since UT is inadequate method of "permanent record".

I maybe wrong but wish helpful.


 
 Reply 
 
HAREESH KUMAR
HAREESH KUMAR
07:00 Nov-20-2011
Re: ISO 13847:2000 Porosity and UT
In Reply to Ed Ginzel at 03:39 Jan-19-2004 (Opening).

My opinion is like ASME, ISO13847 should create an acceptance criteria specifically for Ultrasonic Examination instead of refering to the Radiographic acceptance paragraph, which makes more confusion in establishing Ultrasonic acceptance standard.
Regards,
HAREESH KUMAR

 
 Reply 
 
standards
standards
13:16 Nov-22-2011
Re: ISO 13847:2000 Porosity and UT
In Reply to Ed Ginzel at 03:39 Jan-19-2004 (Opening).

This International Standard specifies the requirements for producing and inspecting girth, branch and fillet welds in the pipeline part of pipeline transportation systems for the petroleum and natural gas industries meeting the requirements of ISO 13623.

http://www.bsb.co.in/

 
 Reply 
 
John O'Brien
Consultant, -
Chevron ETC , USA, Joined Jan 2000, 280

John O'Brien

Consultant, -
Chevron ETC ,
USA,
Joined Jan 2000
280
16:20 Nov-23-2011
Re: ISO 13847:2000 Porosity and UT
In Reply to Ed Ginzel at 03:39 Jan-19-2004 (Opening).

Ed

you are correct its nonsense and was not fixed on the 2001 correction. I question why anyone is using a standard more than a decade old which means the wording is probably 12 or more years old in a fast moving technology environment.

I believe this standard falls under TC 67/SC2 Current Chair is Dennis Tikhomirov. You could send your inquiry through Mrs Kirsi Silander silander@iso.org

Good luck if you get anything positive please post here to help close the loop.

 
 Reply 
 

Product Spotlight

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

Surf-X® Array Probe

Introducing the Surf-X family of flexible Eddy Current Array (ECA) probes. Featuring unique multiple
...
coil sets and proprietary X-PROBE technology, Surf-X array probes can quickly and accurately handle a range of inspection applications, from inspecting corrosion or cracking in pipes, pressure vessels, or tanks, to assessing and sizing cracks in raised welds and friction stir welds.
>

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window