where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

628 views
Technical Discussions
Oliver Brunke
R & D
ZARM - University of Bremen, Germany, Joined Apr 2002, 1

Oliver Brunke

R & D
ZARM - University of Bremen,
Germany,
Joined Apr 2002
1
04:39 Apr-19-2002
monitoring of liquid metal foams with non contact ultrasonics?

Hello everybody,

in the frame of a research project our aim is to monitor the density and porosity of liquid Aluminium-foams. For the foaming process the samples will be placed in cylindrical containers of approximately 25mm diameter in a furnace at Temperatures around 600-700°C.
We think about using non contact ultrasonic transducers for this purpose. What I'd like to know is if this might be principally possible and if yes what kind of companies I could contact for the transducer design.
Thanks in advance for any kind of help!

Oliver Brunke



 
 Reply 
 
Joe Buckley, Sonatest Plc
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 528

Joe Buckley, Sonatest Plc

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
528
05:15 Apr-19-2002
Re: monitoring of liquid metal foams with non contact ultrasonics?
Are you trying to monitor these while in the furnace?

We have done some work with metallic foams when cold, but doing it hot would be well outside our experience. I think that transducers would be a problem - Very high effciciency piezo materials are required for Non contact 'conventional' UT transducers, which tend to be incompatible with High temperature operation .

Laser UT methods may be feasible?

Good luck
Joe

: Hello everybody,
.
: in the frame of a research project our aim is to monitor the density and porosity of liquid Aluminium-foams. For the foaming process the samples will be placed in cylindrical containers of approximately 25mm diameter in a furnace at Temperatures around 600-700°C.
: We think about using non contact ultrasonic transducers for this purpose. What I'd like to know is if this might be principally possible and if yes what kind of companies I could contact for the transducer design.
: Thanks in advance for any kind of help!
.
: Oliver Brunke
.



 
 Reply 
 
chris edwards
chris edwards
05:49 Apr-19-2002
Re: monitoring of liquid metal foams with non contact ultrasonics?
I have carried out non-contact ultrasound measurements on
partially molten/ fully liquid aluminium alloys using
laser generation and EMAT detection.
In the semi molten state the attenuation is very high but
when the metal is fully melted it the attenuation is very low
and the EMAT detector works efficiently.
One of the samples was made by an OSPREY process and contained a lot of trapped
gas. When melted under vacuum it caused the aluminium to form a foam
and it was not possible to detect any ultrasonic signals.

Laser generation, EMAT detection is possible at temperatures in excess
of 1000 C but it foams are very attenuative at ultrasonic frequencies.




 
 Reply 
 

Product Spotlight

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window