where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

814 views
Technical Discussions
haidar shahri
NDT Inspector
abadan refinery, Iran, Joined Apr 2002, 3

haidar shahri

NDT Inspector
abadan refinery,
Iran,
Joined Apr 2002
3
03:34 May-12-2002
what is...

please tell me 1 what is a code? 2 what is a standard? 3 what is a specification? 4 what is defference between a code a standard and a specification? best regards


 
 Reply 
 
Mark Badrick
Inspection
Bahrain Petroleum Co, Bahrain, Joined Oct 1999, 11

Mark Badrick

Inspection
Bahrain Petroleum Co,
Bahrain,
Joined Oct 1999
11
04:05 May-12-2002
Re: what is...
I am confused and please forgive me if you think I am being rude, but your profile states that you are an NDT Inspector at Abdan Refinery with your main methods being MT, PT, RT, UT etc.. In your position it seems a strange question to ask.

: please tell me 1 what is a code? 2 what is a standard? 3 what is a specification? 4 what is defference between a code a standard and a specification? best regards
.



 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1307

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1307
05:39 May-12-2002
Re: what is...
Perhaps this question is not as simple as it may sound. English is full of subtlties in language (e.g. "should" and "shall" are often not noted as different when translated outside of English). As well, specific technical implications do not always have the same meaning in English and American (not to mention spelling!).

I provide below a heirarchy of the document types that are asked about. To the list I have added "procedure" and "technique" which are also sometimes used with different or inter-changeable meaning. Others may have slightly different notions of the meanings of these words.

The terms "code", "standard", "specification" and "procedure" are often confused in NDT. In some cases these terms are used inter-changeably. However from a technical point of view each refers to a separate type of document. To avoid even further confusion we will restrict our definitions to the written documents implied by these terms. This caution is due to the common referral to calibration blocks or test pieces with known defects used to verify accuracy of a test procedure as a "standard".

A standard is a written document assembled by recognized experts, with the purpose of recommending actions to achieve certain objectives. An example of a standard is the American Society of Nondestructive Testing Recommended Practice No. SNT-TC-1A. This is a standard for qualification and certification of NDT personnel by employers.

A standard is usually enforced or given authority by an organization or agency (typically professional societies or national institutions). When a set of standards is incorporated into law and thereby enforceable legally it is considered a code. Examples of codes are:
-American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code
-Canadian Standards Association (CSA) Z662 Oil & Gas Pipeline Systems.

When a user or purchaser of a specific product requires assurance of quality level they will often arrange their own document describing specific test parameters and acceptance criteria. Such a product specific standard is considered a specification. Although it may reference other codes and standards it can require more stringent limits than the more general standards.

To avoid the ambiguity of the usually general standards, and to avoid the constant updating of specifications that refer to national standards which are constantly revised, companies often develop a procedure.

The procedure can address the company's needs by setting out its standard practices for the various aspects of the test method, such as; procurement, processing, periodic controls, approved materials and accessories.

Finally, as a contracted inspection company applies a test to various parts, the variations available to achieve the desired results can be too myriad to list as part of the procedure document and generalisations are again too vague. A common method of addressing the specific inspection application to a specific part is to use a technique sheet.
**********************************************

: please tell me 1 what is a code? 2 what is a standard? 3 what is a specification? 4 what is defference between a code a standard and a specification? best regards
.



 
 Reply 
 

Product Spotlight

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

PAUT Probes

Typical Phased Array probes have frequencies between 1MHz and 20MHz and the number of wafers is 10
...
to 128. M2 Electronics offers customers conventionally ultrasound probes and the ability to provide high-precision Phased Array Ultrasound Probes of up to 256 wafers. We can also customize the probe for our customers to meet the specific application requirements of the user.
>

Wireless TOFD scanner

Quick, accurate and highly reproducible welds testing. The System operates wirelessly and is compat
...
ible with any type of Windows based Laptop, Desktop or Tablet.
>

Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)

Download our white paper on Scatter Correction for Industrial Cone-Beam Computed Tomography (CBCT)
...
Using 3D VSHARP, a fast GPU-Based Linear Boltzmann Transport Equation Solver here: http://bit.ly/2Y0t78P
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window