where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
414 views
Technical Discussions
SK mohiuddin
SK mohiuddin
06:15 May-18-2002
NDT Practical examination

I have seen different ways by different L3 conducting practical examination, may be based on respective written practice. There are many check points that we can institute on the candidate before evaluating his proficiency. In this regard, I would like to know from guru's in the forum, what is the best way of conducting a practical examination for level II and Level I as per ASNT. Is it required for a L3 to be present while L2/L1 is being tested for practical? I think only evaluation is to be done by L3 whereas invigilator can be anyone.

Some of the check points I feel are...please share your views for the benefit of all

1) Check the candidates proficiency in handling and setting the equipment/process
2) whether candidate could able to detect the defect, if yes was the dimentions (location and size) is as per the master document ( within +/- 10% normally full marks) and more depart from actual values will reduce the marks proportionally. In some cases the cracks in specimen is very minute, in these cases full marks for detecting.
3) how good is the candidates report.
4) normally 2 specimens is recommended for the above

thanks
moin


 
 Reply 
 
mike doglas
mike doglas
02:45 Jul-03-2002
Re: NDT Practical examination
: I have seen different ways by different L3 conducting practical examination, may be based on respective written practice. There are many check points that we can institute on the candidate before evaluating his proficiency. In this regard, I would like to know from guru's in the forum, what is the best way of conducting a practical examination for level II and Level I as per ASNT. Is it required for a L3 to be present while L2/L1 is being tested for practical? I think only evaluation is to be done by L3 whereas invigilator can be anyone.
.
: Some of the check points I feel are...please share your views for the benefit of all
.
: 1) Check the candidates proficiency in handling and setting the equipment/process
: 2) whether candidate could able to detect the defect, if yes was the dimentions (location and size) is as per the master document ( within +/- 10% normally full marks) and more depart from actual values will reduce the marks proportionally. In some cases the cracks in specimen is very minute, in these cases full marks for detecting.
: 3) how good is the candidates report.
: 4) normally 2 specimens is recommended for the above
.
: thanks
: moin
.mike doglas



 
 Reply 
 

Product Spotlight

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Surf-X® Array Probe

Introducing the Surf-X family of flexible Eddy Current Array (ECA) probes. Featuring unique multiple
...
coil sets and proprietary X-PROBE technology, Surf-X array probes can quickly and accurately handle a range of inspection applications, from inspecting corrosion or cracking in pipes, pressure vessels, or tanks, to assessing and sizing cracks in raised welds and friction stir welds.
>

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

FD800 Bench Top Flaw Detectors

The bench-top FD800 flaw detector range combines state-of-the-art flaw detection with advanced mater
...
ial thickness capabilities. Designed for use in the laboratory these gauges are the tool you need for all your flaw detecting needs.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window