where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

293 views
Technical Discussions
Xavier
Xavier
05:22 Jun-07-2002
European Post-doc and visiting scientist positions

FOR MORE INFORMATION, CONTACT DIRECTLY Dr A. Eriksson by e-mail eriksson@jrc.nl

Post Doc Fellowships and visiting scientist fellowships at ENIQ / Inspection Management Sector

The Inspection Management Sector of the Institute of Energy is the operating agent of ENIQ –the European Network for Inspection and Qualification. The sector performs research, usually in multi-partner projects in order to i) assess and qualify non destructive evaluation inspection techniques and procedures primarily for nuclear components, ii) harmonise codes and standards at European level in the field of Inspection Qualification and Risk-informed In-service Inspection and to iii) set up a co-ordinated EU approach for qualification of in-service inspection. ENIQ covers pilot studies simulating in-service inspections, qualification of in-service inspections, drawing up of recommended practices for inspection qualification, verifying the feasibility to implement a European system of recognition at European level of inspection qualification exercises and studying risk informed concepts and their influence on inspection qualification. We are now announcing the following fellowships:

1. Post-doc Fellowship for a scientist with experience in risk informed decision-making techniques for inspection and/or maintenance planning. Knowledge in probabilistic risk analysis is desirable. The candidate should hold a Ph.D. (or equivalent experience) in a field like mechanical engineering, nuclear engineering or physics.

2. Post-doc Fellowship for a specialist in ultrasonics, experimental and/or modelling. Possible areas to be covered are: applications of ultrasonic Phased Array system to in-service inspection (ISI) problems; inspection problems/modelling of austenitic welds (scattering, attenuation, beam skewing etc), modelling and simulation of ultrasonic ISI. The candidate should hold a Ph.D. (or equivalent experience) in a field like mechanical engineering, nuclear engineering or physics.

3. Post-doc Fellowship for an inspection qualification specialist with knowledge in the use of technical justification in the qualification process, modelling, reliability studies of the different components in the In-service Inspection system (procedures, equipment and personnel). Experience with ultrasonics is desirable, but other techniques are also welcome. The candidate should hold a Ph.D. (or equivalent experience) in a field like mechanical engineering, nuclear engineering or physics.

4. Visiting scientists (all nationalities, less than 65 years old, with good track record in NDT R&D on the topics described in points 1, 2 and 3). More information on request.

Minimum requirements :
- to be less than 35 years old (Visiting scientists: less than 65 years old)
- to be a European citizen (or a member of an associated states) – Visiting scientists (any nationalities)
- to have a PhD degree

Contract duration: 2 ~ 3 years.
Location: The Netherlands, Europe.

FOR MORE INFORMATION, CONTACT DIRECTLY Dr A. Eriksson by e-mail:
eriksson@jrc.nl



 
 Reply 
 

Product Spotlight

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

OPBOX with standard software is able to do all types of inspections and measurements: flaw detection in welds and materials, scanning of objects, testing composite materials, forged and moulded pieces, many UT inspections, measurements of properties of ma

Typical applications: UT measurements with pulse technique, Measurement of thicknesses also at hig
...
h temperatures, Measurements of properties of materials, including fluids and gases We are delivering a standard version of the software (for any Microsoft Windows up to 10 x64 with Microsoft Hardware certification report Approved) and for special needs: SDK with ready to use examples for LabView, MATLAB x64, C++ wrapper for dll, Python and Linux., and also low-level description of how to control our devices directly from any USB tools
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window