where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
687 views
Technical Discussions
Milan
NDT Inspector
U.S.Steel Kosice s.r.o, Slovak Republic, Joined Aug 2002, 4

Milan

NDT Inspector
U.S.Steel Kosice s.r.o,
Slovak Republic,
Joined Aug 2002
4
03:34 Aug-12-2002
Thickness measurement

Hello everybody.
May somebody help me?
I need measure thickness of pipewall but I have one trouble.
Diameter of pipeline is 2500mm, and thickness of pipe wall is about 6-10mm.
I have apparatus DM-2LCDM with transducer DA211.
And what trouble?
This pipe is in blast furnance. Its leaning gas tubing.Entrance to the pipeline is only from one side(from above), and is impossible go round all pipe because its much high(60m).But I need measure all surface, but my hand is too short.(diameter 2500mm). Do you know how can I solve this trouble?
Thank you.
Milan
Sorry for my poor english.


 
 Reply 
 
Richard Kazares
Richard Kazares
06:44 Aug-12-2002
Re: Thickness measurement
You have an interesting problem - and I think we have a good solution for you - we manufacture a CONFIGURABLE magnetic scanner - that can easly go around the inside of a 2500 mm pipe - and perform a 100% thickness survery for you.

If you follow the link below to our website and get information on LSI (Large Structure Inspection) System.

It would be more than likely that we can help you perform this test - we have systems available for use in North America (4 systems), Europe (4 systems), the Middle East (1 system), South America (2 systems) and Japan (1 system).

Alternatively, you may contact me directly for more information.

Richard Kazares
General Manager
NDT Automation
1-619-716-4123

: Hello everybody.
: May somebody help me?
: I need measure thickness of pipewall but I have one trouble.
: Diameter of pipeline is 2500mm, and thickness of pipe wall is about 6-10mm.
: I have apparatus DM-2LCDM with transducer DA211.
: And what trouble?
: This pipe is in blast furnance. Its leaning gas tubing.Entrance to the pipeline is only from one side(from above), and is impossible go round all pipe because its much high(60m).But I need measure all surface, but my hand is too short.(diameter 2500mm). Do you know how can I solve this trouble?
: Thank you.
: Milan
: Sorry for my poor english.
.



 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
07:30 Aug-13-2002
Re: Thickness measurement
From what Mr.Milan wrote, I got the impression that he cannot access the ID of the pipe, but can access the pipe only from OD and that too from above. In such a case, a magnetic crawler or a ring with the probe mounted by a spring so that contact is assured can be tried.

If he clarifies the access (from OD or ID), the solutions can be thought of.


: You have an interesting problem - and I think we have a good solution for you - we manufacture a CONFIGURABLE magnetic scanner - that can easly go around the inside of a 2500 mm pipe - and perform a 100% thickness survery for you.
.
: If you follow the link below to our website and get information on LSI (Large Structure Inspection) System.
.
: It would be more than likely that we can help you perform this test - we have systems available for use in North America (4 systems), Europe (4 systems), the Middle East (1 system), South America (2 systems) and Japan (1 system).
.
: Alternatively, you may contact me directly for more information.
.
: Richard Kazares
: General Manager
: NDT Automation
: 1-619-716-4123
.
.
: : Hello everybody.
: : May somebody help me?
: : I need measure thickness of pipewall but I have one trouble.
: : Diameter of pipeline is 2500mm, and thickness of pipe wall is about 6-10mm.
: : I have apparatus DM-2LCDM with transducer DA211.
: : And what trouble?
: : This pipe is in blast furnance. Its leaning gas tubing.Entrance to the pipeline is only from one side(from above), and is impossible go round all pipe because its much high(60m).But I need measure all surface, but my hand is too short.(diameter 2500mm). Do you know how can I solve this trouble?
: : Thank you.
: : Milan
: : Sorry for my poor english.
: .
.



 
 Reply 
 

Product Spotlight

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

Magnetic X-Ray Pipeline Crawler

Zhong Yi brand pipeline crawler is magnetic/micro-video controlled crawler with DC X ray unit inst
...
alled for checking welding of pipeline. Move steadily inside the pipeline 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometers and provide the efficient inspection of the pipeline.
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

XRHRobotStar

In high volume industries like automotive the requirement for a hundred percent X-ray inspection c
...
reates a bottleneck in the production. The XRHRobotStar is a fully Automated Defect Recognition (ADR) capable robot-system that allows an ultra-fast in-line inspection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window