where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
686 views
Technical Discussions
Milan
NDT Inspector
U.S.Steel Kosice s.r.o, Slovak Republic, Joined Aug 2002, 4

Milan

NDT Inspector
U.S.Steel Kosice s.r.o,
Slovak Republic,
Joined Aug 2002
4
03:34 Aug-12-2002
Thickness measurement

Hello everybody.
May somebody help me?
I need measure thickness of pipewall but I have one trouble.
Diameter of pipeline is 2500mm, and thickness of pipe wall is about 6-10mm.
I have apparatus DM-2LCDM with transducer DA211.
And what trouble?
This pipe is in blast furnance. Its leaning gas tubing.Entrance to the pipeline is only from one side(from above), and is impossible go round all pipe because its much high(60m).But I need measure all surface, but my hand is too short.(diameter 2500mm). Do you know how can I solve this trouble?
Thank you.
Milan
Sorry for my poor english.


 
 Reply 
 
Richard Kazares
Richard Kazares
06:44 Aug-12-2002
Re: Thickness measurement
You have an interesting problem - and I think we have a good solution for you - we manufacture a CONFIGURABLE magnetic scanner - that can easly go around the inside of a 2500 mm pipe - and perform a 100% thickness survery for you.

If you follow the link below to our website and get information on LSI (Large Structure Inspection) System.

It would be more than likely that we can help you perform this test - we have systems available for use in North America (4 systems), Europe (4 systems), the Middle East (1 system), South America (2 systems) and Japan (1 system).

Alternatively, you may contact me directly for more information.

Richard Kazares
General Manager
NDT Automation
1-619-716-4123

: Hello everybody.
: May somebody help me?
: I need measure thickness of pipewall but I have one trouble.
: Diameter of pipeline is 2500mm, and thickness of pipe wall is about 6-10mm.
: I have apparatus DM-2LCDM with transducer DA211.
: And what trouble?
: This pipe is in blast furnance. Its leaning gas tubing.Entrance to the pipeline is only from one side(from above), and is impossible go round all pipe because its much high(60m).But I need measure all surface, but my hand is too short.(diameter 2500mm). Do you know how can I solve this trouble?
: Thank you.
: Milan
: Sorry for my poor english.
.



 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
07:30 Aug-13-2002
Re: Thickness measurement
From what Mr.Milan wrote, I got the impression that he cannot access the ID of the pipe, but can access the pipe only from OD and that too from above. In such a case, a magnetic crawler or a ring with the probe mounted by a spring so that contact is assured can be tried.

If he clarifies the access (from OD or ID), the solutions can be thought of.


: You have an interesting problem - and I think we have a good solution for you - we manufacture a CONFIGURABLE magnetic scanner - that can easly go around the inside of a 2500 mm pipe - and perform a 100% thickness survery for you.
.
: If you follow the link below to our website and get information on LSI (Large Structure Inspection) System.
.
: It would be more than likely that we can help you perform this test - we have systems available for use in North America (4 systems), Europe (4 systems), the Middle East (1 system), South America (2 systems) and Japan (1 system).
.
: Alternatively, you may contact me directly for more information.
.
: Richard Kazares
: General Manager
: NDT Automation
: 1-619-716-4123
.
.
: : Hello everybody.
: : May somebody help me?
: : I need measure thickness of pipewall but I have one trouble.
: : Diameter of pipeline is 2500mm, and thickness of pipe wall is about 6-10mm.
: : I have apparatus DM-2LCDM with transducer DA211.
: : And what trouble?
: : This pipe is in blast furnance. Its leaning gas tubing.Entrance to the pipeline is only from one side(from above), and is impossible go round all pipe because its much high(60m).But I need measure all surface, but my hand is too short.(diameter 2500mm). Do you know how can I solve this trouble?
: : Thank you.
: : Milan
: : Sorry for my poor english.
: .
.



 
 Reply 
 

Product Spotlight

XRHRobotStar

In high volume industries like automotive the requirement for a hundred percent X-ray inspection c
...
reates a bottleneck in the production. The XRHRobotStar is a fully Automated Defect Recognition (ADR) capable robot-system that allows an ultra-fast in-line inspection.
>

Wireless TOFD scanner

Quick, accurate and highly reproducible welds testing. The System operates wirelessly and is compat
...
ible with any type of Windows based Laptop, Desktop or Tablet.
>

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window