where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

VOGT Ultrasonics GmbH
non-destructive testing, services, training, ultrasonic systems, immersion and squirter inspection systems, PROline, digital radiology
1862 views
Technical Discussions
Ing. Tomás Pérez Abrego
NDT Inspector
Refineria Panama,S.A. (TEXACO), Algeria, Joined Dec 1999, 3

Ing. Tomás Pérez Abrego

NDT Inspector
Refineria Panama,S.A. (TEXACO),
Algeria,
Joined Dec 1999
3
07:15 Dec-17-1999
UT flaw detector

I need information about:

1. calibration of ultrasonic flaw detector EPOCH III-MODEL2300 (PANAMETRIC):

1.A. Initial settings
1.B. Straight beam calibration
1.C. Angle beam transducer calibration.
1.D. Verification of linearity.
1.E. What kind of calibrations block I should use?

And all data about operation of ultrasonic flaw detector epcho III-model 2300 (Panametric). I'll be glad you send me, all information at perezt@texaco.com E-mail.

Thank you very much.

Regards

T.Perez A.




 
 Reply 
 
Ing. Manuel Haces
Ing. Manuel Haces
08:01 Dec-17-1999
Re: UT flaw detector



 
 Reply 
 
Godfrey Hands
Consultant,
PRI Nadcap, United Kingdom, Joined Nov 1998, 303

Godfrey Hands

Consultant,
PRI Nadcap,
United Kingdom,
Joined Nov 1998
303
00:04 Dec-18-1999
Re: UT flaw detector
ck the specification that you need to test against, and see what the operator qualification requirements are.

The training and experience requirements were taken directly from the recommended practice for NDT training from the American Society of Nondestructive Testing (ASNT), document SNT-TC-1A.

Godfrey Hands



 
 Reply 
 
Mark Davis
Teacher, And Consultant
University of Ultrasonics, Birmingham, Alabama, USA, Joined Mar 2000, 85

Mark Davis

Teacher, And Consultant
University of Ultrasonics, Birmingham, Alabama,
USA,
Joined Mar 2000
85
02:49 Dec-19-1999
Re: UT flaw detector



 
 Reply 
 
Eng. Fathi Ghanameh
Eng. Fathi Ghanameh
01:30 Dec-22-1999
Re: UT flaw detector



 
 Reply 
 
Bambang Wahyudi
Bambang Wahyudi
05:38 Aug-10-2000
Re: UT flaw detector



 
 Reply 
 
Bambang Wahyudi
Bambang Wahyudi
01:00 Apr-08-2001
Re: UT flaw detector
: : I need information about:

: : 1. calibration of ultrasonic flaw detector EPOCH III-MODEL2300 (PANAMETRIC):

: : 1.A. Initial settings
: : 1.B. Straight beam calibration
: : 1.C. Angle beam transducer calibration.
: : 1.D. Verification of linearity.
: : 1.E. What kind of calibrations block I should use?

: : And all data about operation of ultrasonic flaw detector epcho III-model 2300 (Panametric). I'll be glad you send me, all information at perezt@texaco.com E-mail.

: : Thank you very much.

: : Regards

: : T.Perez A.

: : I am a consultant trainer for Panametrics. I agree with a previous comment that you should contact Panametrics or your Panametrics distributor. You should attend panametrics training. You actually need 80 hours of training in ultrsonics theory, applications, and use. Panametrics can provide the training and the training on the EPOCH III.

: Good Luck,

: J. Mark Davis

I need information about Panametrics DL 36 plus.

Thx
Bambang Wahyudi




 
 Reply 
 
David Hermanutz
Consultant,
Hbndt.com, China, Joined Jul 2012, 85

David Hermanutz

Consultant,
Hbndt.com,
China,
Joined Jul 2012
85
01:04 Apr-09-2001
Re: UT flaw detector
: : : I need information about:
.
: : : 1. calibration of ultrasonic flaw detector EPOCH III-MODEL2300 (PANAMETRIC):
.
: : : 1.A. Initial settings
: : : 1.B. Straight beam calibration
: : : 1.C. Angle beam transducer calibration.
: : : 1.D. Verification of linearity.
: : : 1.E. What kind of calibrations block I should use?
.
: : : And all data about operation of ultrasonic flaw detector epcho III-model 2300 (Panametric). I'll be glad you send me, all information at perezt@texaco.com E-mail.
.
: : : Thank you very much.
.
: : : Regards
.
: : : T.Perez A.
.
: : : I am a consultant trainer for Panametrics. I agree with a previous comment that you should contact Panametrics or your Panametrics distributor. You should attend panametrics training. You actually need 80 hours of training in ultrsonics theory, applications, and use. Panametrics can provide the training and the training on the EPOCH III.
.
: : Good Luck,
.
: : J. Mark Davis
.
: I need information about Panametrics DL 36 plus.
.
: Thx
: Bambang Wahyudi

Dear Sirs,

I am the resident Epoch 3 and 36dlplus expert for Panametrics in Australia. I have several hundred calibration settings for the Epoch 3 and can offer the basic settings to you to get you started on your Epoch 3 instrument. I can also offer other training information as your needs arise.

Please send me a personal email to

hermanutzd@panametrics.com.au

with your company details, panametric equipment model numbers (probes and calibration blocks )and I will endeavor to assist you and also put you in contact with your nearest Panametrics expert.

Best Regards.

David Hermanutz
Panametrics Melbourne



 
 Reply 
 
Tran Ngoc Minh
Tran Ngoc Minh
01:12 Apr-09-2001
Re: UT flaw detector
Dear Sir
: : I need information about:

: : 1. calibration of ultrasonic flaw detector EPOCH III-MODEL2300 (PANAMETRIC):

: : 1.A. Initial settings
: : 1.B. Straight beam calibration
: : 1.C. Angle beam transducer calibration.
: : 1.D. Verification of linearity.
: : 1.E. What kind of calibrations block I should use?

: : And all data about operation of ultrasonic flaw detector epcho III-model 2300 (Panametric). I'll be glad you send me, all information at perezt@texaco.com E-mail.

: : Thank you very much.

: : Regards

: : T.Perez A.

: : I am a consultant trainer for Panametrics. I agree with a previous comment that you should contact Panametrics or your Panametrics distributor. You should attend panametrics training. You actually need 80 hours of training in ultrsonics theory, applications, and use. Panametrics can provide the training and the training on the EPOCH III.

: Good Luck,

: J. Mark Davis




 
 Reply 
 
florian rutahindurwa
florian rutahindurwa
02:08 Jan-11-2002
Re: UT flaw detector
kindly please facilitate me with information on the method (and the method itself) of determining nodularity in ductile iron castings using the UT detector


 
 Reply 
 
Santiago Duran
Santiago Duran
00:38 Sep-01-2002
informations
I want to buy a ultrasonic flaw detector used....
diferent option panametric epoch series, krautkramer
give me de the best price...
thanks...


 
 Reply 
 
A. Gkiokas
NDT Inspector, Consultant (Level 3)
NDT TECHNOLOGY, Greece, Joined Aug 2001, 2

A. Gkiokas

NDT Inspector, Consultant (Level 3)
NDT TECHNOLOGY,
Greece,
Joined Aug 2001
2
01:58 Sep-03-2002
Re: informations
: I want to buy a ultrasonic flaw detector used....
: diferent option panametric epoch series, krautkramer
: give me de the best price...
: thanks...
.

Krautkramer USN-52 - 6350 Euro


 
 Reply 
 

Product Spotlight

Wireless TOFD scanner

Quick, accurate and highly reproducible welds testing. The System operates wirelessly and is compat
...
ible with any type of Windows based Laptop, Desktop or Tablet.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window