where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
579 views
Technical Discussions
Brian Younce
Brian Younce
00:55 Oct-09-2002
Pre-penetrant Surface Prep of an EDM Cut Aluminum Surface

Folks,

I am wondering if anyone can reference me to information regarding surface preparation of an EDM cut aluminum surface that is to be penetrant inspected. My concerns are whether etching should be required or not, if so how aggressive of an etch, if not is there a different surface prep that is recommended. Does the EDM process have the tendency to smear metal, close pre-existing discontinuities, create new discontinuities?

I am not familiar with the EDM process, therefore I have more questions than answers at this point and would appreciate any input from anyone who does have some experience.

Thanks in advance for your time,

Brian Younce
NDT Level III
Hartzell Propeller Inc.



    
 
 Reply 
 
Phil Herman Jr.
Sales, - Manufacture of NDT Reference Standards/Test Blocks
PH Tool Reference Standards, USA, Joined Oct 1999, 79

Phil Herman Jr.

Sales, - Manufacture of NDT Reference Standards/Test Blocks
PH Tool Reference Standards,
USA,
Joined Oct 1999
79
01:15 Oct-09-2002
Re: Pre-penetrant Surface Prep of an EDM Cut Aluminum Surface
Brian,

PH Tool Reference Standards manufactures EDM notch standards and test blocks for all NDT disciplines. While we are most familiar with the "micro-machining" of narrow notches and slots, we also perform both conventional (a.k.a. sinker) and wire EDM. It would be helpful to know which process was used to manufacture the aluminum parts you need to PT. Feel free to contact me directly at 888-553-9245 or philjr@phtool.com.

Phil Herman Jr.
PH Tool


: Folks,
.
: I am wondering if anyone can reference me to information regarding surface preparation of an EDM cut aluminum surface that is to be penetrant inspected. My concerns are whether etching should be required or not, if so how aggressive of an etch, if not is there a different surface prep that is recommended. Does the EDM process have the tendency to smear metal, close pre-existing discontinuities, create new discontinuities?
.
: I am not familiar with the EDM process, therefore I have more questions than answers at this pointand would appreciate any input from anyone who does have some experience.
.
: Thanks in advance for your time,
.
: Brian Younce
: NDT Level III
: Hartzell Propeller Inc.
.



    
 
 Reply 
 
Sergio Bilbao
Sergio Bilbao
01:29 Oct-09-2002
Re: Pre-penetrant Surface Prep of an EDM Cut Aluminum Surface

Brian,

It depends on how your EDM Process in made.
For example, the roughness you are achieving. Anyway, EDM machined surfaces have a surface quality quite good.
If you are going to make a sensitivity 2 FP Inspection, it is probably you will get an acceptable background.

The EDM's most important characteristic is that it modifies the grain size in the subsurface layer, known as "Recast Layer". But it is not important for the FPI.

The EDM does not close discontinuities. And generally, doesn't create news indications.

Be care of oxidations and burns.

Regards.


: Folks,
.
: I am wondering if anyone can reference me to information regarding surface preparation of an EDM cut aluminum surface that is to be penetrant inspected. My concerns are whether etching should be required or not, if so how aggressive of an etch, if not is there a different surface prep that is recommended. Does the EDM process have the tendency to smear metal, close pre-existing discontinuities, create newdiscontinuities?
.
: I am not familiar with the EDM process, therefore I have more questions than answers at this point and would appreciate any input from anyone who does have some experience.
.
: Thanks in advance for your time,
.
: Brian Younce
: NDT Level III
: Hartzell Propeller Inc.
.



    
 
 Reply 
 

Product Spotlight

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

Lyft™: Pulsed Eddy Current Reinvented

PEC Reinvented—CUI Programs Redefined Corrosion under insulation (CUI) is possibly the greatest u
...
nresolved asset integrity problem in the industry. Current methods for measuring wall thickness with liftoff, without removing insulation, all have severe limitations. Eddyfi introduces Lyft — a reinvented, high-performance pulsed eddy current (PEC) solution. The patent- pending system features a state-of-the-art portable instrument, real- time C-scan imaging, fast data acquisition with grid-mapping and dynamic scanning modes, and flexibility with long cables. It can also scan through thick metal and insulation, as well as aluminum, stainless steel, and galvanized steel weather jackets. Who else but Eddyfi to reinvent an eddy current technique and redefine CUI programs. Got Lyft?
>

GUL QSR1® Scanning

How do you measure pipe wall thickness without direct access to the area? QSR® Scanning - Guide Wav
...
e Quantitative Short Range Scanning.
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window