where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1021 views
Technical Discussions
Doug Breeze
Director, Consultant; R&D
Inspection Software Limited, United Kingdom, Joined May 2000, 20

Doug Breeze

Director, Consultant; R&D
Inspection Software Limited,
United Kingdom,
Joined May 2000
20
03:51 Oct-24-2002
Accredited NDT Degree Courses in UK

Gentlemen,

On behalf of an overseas student, I'm looking for Insitutions in UK that offer full-time 2-3 year degree courses in Non-Destructive-Testing, as an alternative to his studies in USA.

Only UK institutions or references to them, should respond please with contact details to acquire a prospectus.
Many thanks.

Doug Breeze


 
 Reply 
 
Isac Einstein
Isac Einstein
00:04 Oct-25-2002
Re: Accredited NDT Degree Courses in UK
There ain't any


 
 Reply 
 
Martin Lugg
Consultant,
Eddyfi Technologies, United Kingdom, Joined Nov 2000, 27

Martin Lugg

Consultant,
Eddyfi Technologies,
United Kingdom,
Joined Nov 2000
27
00:40 Oct-25-2002
Re: Accredited NDT Degree Courses in UK
: Gentlemen,
.
: On behalf of an overseas student, I'm looking for Insitutions in UK that offer full-time 2-3 year degree courses in Non-Destructive-Testing, as an alternative to his studies in USA.
.
: Only UK institutions or references to them, should respond please with contact details to acquire a prospectus.
: Many thanks.
.
: Doug Breeze
.
According to Bill Dover at UCL:

The only one that used to run was the one at Brunel which was an MSc. This
is almost certainly finished. The only other faint possibility is Professor
Bridge who I think is now at Westminster College.



 
 Reply 
 
Robert Paynter
R & D,
U of Oxford, United Kingdom, Joined Jun 2001, 14

Robert Paynter

R & D,
U of Oxford,
United Kingdom,
Joined Jun 2001
14
01:49 Oct-28-2002
Re: Accredited NDT Degree Courses in UK
: Insitutions in UK that offer full-time 2-3 year
: degree courses in Non-Destructive-Testing, as an
: alternative to his studies in USA.

NDT is not regarded as a wide enough topic to deserve a first degreee. Most engineering courses would entertain a final year project focussing on a use of NDT. Most UK engineering degrees are 4 years.

The British institute of NDT training institutes page:
http://www.bindt.org/Mk1Site/Training.html


 
 Reply 
 

Product Spotlight

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window