where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
841 views
Technical Discussions
Hason
Hason
08:13 Nov-09-2002
pulse amplifer wanted

I want to buy a high frequency(20MHz) pulse amplifer to amplify the pulsed sine wave to drive PZT transducer. the requirement: output voltage: Vp-p>=100V. Could anyone provide some information?


 
 Reply 
 
JM lecoeur
Director
LECOEUR ELECTRONIQUE, France, Joined Nov 1998, 1

JM lecoeur

Director
LECOEUR ELECTRONIQUE,
France,
Joined Nov 1998
1
00:05 Nov-10-2002
Re: pulse amplifer wanted
: I want to buy a high frequency(20MHz) pulse amplifer to amplify the pulsed sine wave to drive PZT transducer. the requirement: output voltage: Vp-p>=100V. Could anyone provide some information?

We have some pulse amplifers (analog and square).


 
 Reply 
 
Kevin Barton
Kevin Barton
02:10 Nov-11-2002
Re: pulse amplifer wanted
Dear Hanson,

We have a two Preamplifiers in the 20MHz frequency range. The first unit is a 5676 and has a bandwidth of 20MHz and the second unit is a 5678 and a has a 40MHz bandwidth. The receiver bandwidth for both of these units is based on a -3db specification. For example, if you are using 20MHz frequency, I would go with the 5678 because the 5676 would cut off some of the frequency. In addition, you may purchase the unit in either a DC battery operated configuration or a AC 115 voltage configuration.

If you have any further questions or would like a firm quotation, please feel free to contact me at the information listed below.

Sincerely,


Kevin M. Barton
Technical Sales Engineer, Instrumentation and Systems
NDT Division of GE Panametrics
221 Crescent Street, Waltham, MA 02453-3497 USA
Tel (781) 472-1260, Fax (781) 788-9787
E-mail: kevin.barton@ps.ge.com
Website: www.panametrics.com

_______________________________________________________
: I want to buya high frequency(20MHz) pulse amplifer to amplify the pulsed sine wave to drive PZT transducer. the requirement: output voltage: Vp-p>=100V. Could anyone provide some information?
.



 
 Reply 
 
Hason
Hason
06:23 Nov-13-2002
Re: pulse amplifer wanted
: : I want to buy a high frequency(20MHz) pulse amplifer to amplify the pulsed sine wave to drive PZT transducer. the requirement: output voltage: Vp-p>=100V. Could anyone provide some information?
.
: We have some pulse amplifers (analog and square).
.
Acturally, we are seeking for a pulse amplifier to amplify the pulsed sine wave provided by function generator to excite the PZT ultrasonic ransducer.
our requirment is: the amplifer can amplify the burst sine wave (20MHz,
10MHz, 5MHz, burst rate 1-10KHz, cycle:4-16) to the voltage of about at least Vp-p=80V.
if a pulser (comine the function of burst wave generation and amplication) can satisfy our requirment. that's also OK!


 
 Reply 
 

Product Spotlight

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

Magnetic X-Ray Pipeline Crawler 6''-60''

Suitable to work in 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometer
...
s and provide the efficient inspection of the pipeline.
>

GUL QSR1® Scanning

How do you measure pipe wall thickness without direct access to the area? QSR® Scanning - Guide Wav
...
e Quantitative Short Range Scanning.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window