where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
842 views
Technical Discussions
Hason
Hason
08:13 Nov-09-2002
pulse amplifer wanted

I want to buy a high frequency(20MHz) pulse amplifer to amplify the pulsed sine wave to drive PZT transducer. the requirement: output voltage: Vp-p>=100V. Could anyone provide some information?


 
 Reply 
 
JM lecoeur
Director
LECOEUR ELECTRONIQUE, France, Joined Nov 1998, 1

JM lecoeur

Director
LECOEUR ELECTRONIQUE,
France,
Joined Nov 1998
1
00:05 Nov-10-2002
Re: pulse amplifer wanted
: I want to buy a high frequency(20MHz) pulse amplifer to amplify the pulsed sine wave to drive PZT transducer. the requirement: output voltage: Vp-p>=100V. Could anyone provide some information?

We have some pulse amplifers (analog and square).


 
 Reply 
 
Kevin Barton
Kevin Barton
02:10 Nov-11-2002
Re: pulse amplifer wanted
Dear Hanson,

We have a two Preamplifiers in the 20MHz frequency range. The first unit is a 5676 and has a bandwidth of 20MHz and the second unit is a 5678 and a has a 40MHz bandwidth. The receiver bandwidth for both of these units is based on a -3db specification. For example, if you are using 20MHz frequency, I would go with the 5678 because the 5676 would cut off some of the frequency. In addition, you may purchase the unit in either a DC battery operated configuration or a AC 115 voltage configuration.

If you have any further questions or would like a firm quotation, please feel free to contact me at the information listed below.

Sincerely,


Kevin M. Barton
Technical Sales Engineer, Instrumentation and Systems
NDT Division of GE Panametrics
221 Crescent Street, Waltham, MA 02453-3497 USA
Tel (781) 472-1260, Fax (781) 788-9787
E-mail: kevin.barton@ps.ge.com
Website: www.panametrics.com

_______________________________________________________
: I want to buya high frequency(20MHz) pulse amplifer to amplify the pulsed sine wave to drive PZT transducer. the requirement: output voltage: Vp-p>=100V. Could anyone provide some information?
.



 
 Reply 
 
Hason
Hason
06:23 Nov-13-2002
Re: pulse amplifer wanted
: : I want to buy a high frequency(20MHz) pulse amplifer to amplify the pulsed sine wave to drive PZT transducer. the requirement: output voltage: Vp-p>=100V. Could anyone provide some information?
.
: We have some pulse amplifers (analog and square).
.
Acturally, we are seeking for a pulse amplifier to amplify the pulsed sine wave provided by function generator to excite the PZT ultrasonic ransducer.
our requirment is: the amplifer can amplify the burst sine wave (20MHz,
10MHz, 5MHz, burst rate 1-10KHz, cycle:4-16) to the voltage of about at least Vp-p=80V.
if a pulser (comine the function of burst wave generation and amplication) can satisfy our requirment. that's also OK!


 
 Reply 
 

Product Spotlight

Teletest Focus+

Teletest Focus+ electronics have superior capabilities than rivals on the market. Beyond the usual
...
test features, Focus+ has 24 transmit channels and 24 receive channels, with an additional on-board switching capabilities. The instrument's frequency range is 10–300 kHz.
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

YXLON Cougar EVO

Scalable small footprint X-ray inspection systems for assembly and laboratory applications. The
...
YXLON Cougar EVO series was designed to provide the "best-in- class" inspection solutions for SMT, semiconductor, and laboratory assembly applications, while maintaining a small system footprint for maximum convenience. With optimized software and hardware, these systems produce higher quality and more consistent results than other electronics inspection systems currently on the market.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window