where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
2386 views
Technical Discussions
hemant suthar
hemant suthar
09:21 Mar-03-2010
regarding asme sec-ix group no.

what is the purpose of group no. in asme sec-ix and on what base it classified.

 
 Reply 
 
Roger Duwe
NDT Inspector, API-510, 570, 653
MISTRAS, USA, Joined Jan 2009, 148

Roger Duwe

NDT Inspector, API-510, 570, 653
MISTRAS,
USA,
Joined Jan 2009
148
18:05 Mar-04-2010
Re: regarding asme sec-ix group no.
In Reply to hemant suthar at 09:21 Mar-03-2010 (Opening).

Mr. Suthar, if you mean Group# [versus P#], the Group#'s are subsets of the P#'s that group materials with similar heat-input and heat-treatment characteristics, per ASME Section IX.
Group# is a Supplementary Essential Variable, and is used for controlled heat input Weld Procedures, like when the Impact Strength at Low Temperature is being tested and recorded during the Procedure Qualification.

 
 Reply 
 
Ganesh V
Other, Site Inspection Supervisor
PDO,Oman, India, Joined Jun 2013, 5

Ganesh V

Other, Site Inspection Supervisor
PDO,Oman,
India,
Joined Jun 2013
5
07:19 Jun-07-2013
Re: regarding asme sec-ix group no.
In Reply to hemant suthar at 09:21 Mar-03-2010 (Opening).

Group Numbers are assigned additionally to P-Numbers. These Group Numbers classify the metals within P-Numbers for the purpose of procedure qualification where notch-toughness ( Charpy V-notch impact test ) requirements are specified.
( Refer : QW.200.3 )

So, whenever the codes requires Impact testing, WPS shall specify the Supplimentary essential variables also, and PQR shall reflect the actual p Number's and its applicable Group Numbers, any changes after in WPS need to be requalified with a PQR again.

 
 Reply 
 
Nelson
Nelson
14:21 Sep-18-2013
Re: regarding asme sec-ix group no.
In Reply to Roger Duwe at 18:05 Mar-04-2010 .

Dear Roger Duwe,

Good info you give. How can i refer that it is related with "similar heat input & heat treatment characteristics" in code. i.e, any asme state these group number has been classified according to this? Please reply.
Thanks in advance.

Neo.

 
 Reply 
 
Roger D. Duwe
NDT Inspector, API-510, 570, 653
MISTRAS, USA, Joined Jan 2009, 148

Roger D. Duwe

NDT Inspector, API-510, 570, 653
MISTRAS,
USA,
Joined Jan 2009
148
19:38 Sep-18-2013
Re: regarding asme sec-ix group no.
In Reply to Nelson at 14:21 Sep-18-2013 .

Nelson, that is so basic that the answer is almost hard. This info comes from the definition of "P#" and "Group#". It is part of the foundation of ASME Sect IX. Without it, every different material spec & grade would require its own individualized PQR and WPS.

 
 Reply 
 

Product Spotlight

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

PAUT Probes

Typical Phased Array probes have frequencies between 1MHz and 20MHz and the number of wafers is 10
...
to 128. M2 Electronics offers customers conventionally ultrasound probes and the ability to provide high-precision Phased Array Ultrasound Probes of up to 256 wafers. We can also customize the probe for our customers to meet the specific application requirements of the user.
>

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window