where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
3807 views
Technical Discussions
Kelly Mock
Kelly Mock
22:25 Oct-15-2013
UT limitations on welded SS thermowells
zoom image

2

zoom image

2

Good day,
What are the practical limitations of UT examination on stainless steel thermowells? Pipe dimensions and flange ratings range but a common size would be approximately a 1.25” OD, .225” wall thickness on the pipe and a 2” 600# flange (approx 1”thick) with 4 to 8 bolt holes, raised face on one side. Weld prep is double J.
Is there a procedure that can satisfy the requirements of ASME B31.3 Normal? The grain boundaries appear to be interrupting shear wave inspection and the bolt holes limit the coverage that a compression wave can manage.
Thanks

 
 Reply 
 
Michel Couture
NDT Inspector,
consultant, Canada, Joined Sep 2006, 889

Michel Couture

NDT Inspector,
consultant,
Canada,
Joined Sep 2006
889
22:33 Oct-15-2013
Re: UT limitations on welded SS thermowells
In Reply to Kelly Mock at 22:25 Oct-15-2013 (Opening).

S'hydratent do UT? This is low operating pressure. How about PT on both side, so each weld and call it a day!

 
 Reply 
 
Kelly Mock
Kelly Mock
22:49 Oct-15-2013
Re: UT limitations on welded SS thermowells
In Reply to Michel Couture at 22:33 Oct-15-2013 .

Unfortunately it is a full penetration weld which they require full examination.

 
 Reply 
 
andrew cunningham
NDT Inspector
Canada, Joined Jun 2008, 238

andrew cunningham

NDT Inspector
Canada,
Joined Jun 2008
238
00:11 Oct-16-2013
Re: UT limitations on welded SS thermowells
In Reply to Kelly Mock at 22:25 Oct-15-2013 (Opening).

A weld scan with shear wave is not possible on SS welds. High angle compression probes may get through but the tooling contours on the sealing face will inhibit the scanning from this surface. You could use a 0 degree from the edge of the flange, but the bolt holes will restrict coverage. Also the stamps on the edge of the flange will need to be smoothed off before scanning. PT the well to flange weld on both sides is the way to go.

All the best

 
 Reply 
 
Csaba Hollo
,
Retired, Canada, Joined Feb 2010, 301

Csaba Hollo

,
Retired,
Canada,
Joined Feb 2010
301
00:42 Oct-16-2013
Re: UT limitations on welded SS thermowells
In Reply to Kelly Mock at 22:25 Oct-15-2013 (Opening).

You can do first leg refracted longitudinal beam sectorial phased array. You would need to do it from both sides of the flange in order to get your coverage.

I would mock up the joint and put calibration reflectors in the root, both fusion faces, especially at the extremities of your scans. Adjust your sensitivity accordingly, and pay attention to where your refracted shear beam reflectors are in the part.

Good luck.

 
 Reply 
 
collin maloney
NDT Inspector, - Plant Inspector
Applus RTD, Australia, Joined Nov 2000, 147

collin maloney

NDT Inspector, - Plant Inspector
Applus RTD,
Australia,
Joined Nov 2000
147
06:34 Oct-16-2013
Re: UT limitations on welded SS thermowells
In Reply to Kelly Mock at 22:49 Oct-15-2013 .

why not set it up like an imersion job. make up a jig and insert probe into the well and test from that way, watch out for water path. Follow up with PT as others have suggested

 
 Reply 
 
Mario Talarico
NDT Inspector,
Italy, Joined May 2010, 423

Mario Talarico

NDT Inspector,
Italy,
Joined May 2010
423
20:39 Oct-16-2013
Re: UT limitations on welded SS thermowells
In Reply to Kelly Mock at 22:25 Oct-15-2013 (Opening).

zoom image

controllo ad immersione

Kelly,
this works!
The thicknesses variables under the probe regulate the height of water in order to allow an input 'clean' without geometric secondary reflections due to the exterior of the weld bead.
Using a sample welded with the same dimensions of the piece to be checked and inserted inside reflectors, must define practically modes: probe (focused or not, frequency, diameter) and height of water for the probe in use (modulated with the thin sheet placed under the probe).
A variation in the angle of flat mirror metal can vary the angle of entry into the flange.
Once achieved the optimum operating conditions remove the sample from the ring, put in its place the workpiece to be checked, and rotates the tube 360 to control 100% of the welding.
Really fast!
Greetings
Mario
 
 Reply 
 
Csaba Hollo
,
Retired, Canada, Joined Feb 2010, 301

Csaba Hollo

,
Retired,
Canada,
Joined Feb 2010
301
21:00 Oct-16-2013
Re: UT limitations on welded SS thermowells
In Reply to Mario Talarico at 20:39 Oct-16-2013 .

I would love to see an ASME procedure for IRIS flaw detection and classification for weld volume/fusion flaws.

It is thinking out of the box for sure, but it might be easier said than done.

PS...Our company owns a few different variations of this sort of equipment, but we only use it for corrosion/erosion of tubular materials.

 
 Reply 
 
Brett Davis
Sales, Sales, Applications, Training, Services, NDT, Pipeline
PTC & DavisBrett LP, USA, Joined Oct 2012, 13

Brett Davis

Sales, Sales, Applications, Training, Services, NDT, Pipeline
PTC & DavisBrett LP,
USA,
Joined Oct 2012
13
20:57 Dec-03-2013
Re: UT limitations on welded SS thermowells
In Reply to Csaba Hollo at 21:00 Oct-16-2013 .

I have tried this very thing using IRIS but did not have sufficient time to finalize my results. I will be receiving my IRIS equipment tomorrow and will be more than happy to assist with this application. Please let me know if there is anything I can do to assist. I have been performing IRIS for 5 years now. Also, I am working on developing a probe that would lend itself very useful for this application. It will not be complete for awhile but if we could find extra funding we could expedite the development and make it a commercial product.

 
 Reply 
 

Product Spotlight

ISONIC 3510

Very Powerful Superior Performance Extremely Portable Smart Phased Array Ultrasonic Flaw Detector an
...
d Recorder with 2 Conventional UT and TOFD Channels uniquely combines PA, single- and multi-channel conventional UT, and TOFD modalities providing 100% raw data recording and imaging. Suitable for all kinds of every-day ultrasonic inspections
>

AIS229 - Multipurpose Real Time System

Latest standard & automatic real time system developed by Balteau. The AIS229 has been designed to
...
do series inspection in a wide variety of industry. Composed of a shielded cabinet, 5 axis manipulator, x-ray generator and tubehead from 160kV to 225kV, a fl at panel & much more, the AIS229 is most certainly one of the most multipurpose RTR system available on the market.
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window