where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
815 views
Technical Discussions
Yasin Karavacýoðlu
Yasin Karavacýoðlu
09:21 Jan-17-2003
ISO 17025

Dear friends;

EN ISO 17025 standard for accreditation testing lab require
that uncertainty measurement. Have any body are there has this info.
thanks


 
 Reply 
 
Uli Mletzko
R & D, Retired
Germany, Joined Nov 1998, 89

Uli Mletzko

R & D, Retired
Germany,
Joined Nov 1998
89
02:39 Jan-17-2003
Re: ISO 17025

: EN ISO 17025 standard for accreditation testing lab require
: that uncertainty measurement. Have any body are there has this info.

To solve the problem, we are using the different terms 'Nondestructive TESTING = non-quantitative NDT' and 'Nondestructive MEASURING = quantitative NDT'.

If you are applying only standard techniques like radiography, ultrasonics for flaw detection, etc., you have to convince the auditor, that this is 'TESTING' and not 'MEASURING', and that therefore ISO 17025 is not applicable.

On the other side, if you are doing wall thickness measuring by ultrasonics, hardening depth measuring by eddy current, corrosion depth measuring by radiography, etc., you or your level-3-man has to know about the accuracy. But this is not a simple task (depending on frequency, film graininess, etc.).

Sometimes, if you have new equipment, or if your equipment is maintenanced periodically by the manufacturer, then the manufacturer possibly could supply you with accuracy data or with a data sheet.

Regards
Uli Mletzko, MPA/NDT,
University of Stuttgart, Germany




 
 Reply 
 
Udo Schlengermann
Consultant, -
Standards Consulting, Germany, Joined Nov 1998, 177

Udo Schlengermann

Consultant, -
Standards Consulting,
Germany,
Joined Nov 1998
177
04:03 Jan-17-2003
Re: ISO 17025
reply by Udo Schlengermann
uschlengermann@agfandt.de:

Standard EN ISO/IEC 17025 is important for all kind of testing and calibration laboratories.

As much as uncertainty is concerned, please read chapter 5.4.6: Estimation of uncertainty of measurement, especially the three notes.
note 1 says that the degree of estimation of uncertainty should be chosen depending on the requirements of the tests, the requirements of the client and depending on existing limits.
note 2 says, that if the test method is well definded (including uncertainty)there is no further need for validation of uncertainty by the test laboratory applying this method.
note 3 gives a hint for further information to ISO 5725 and the "Guide to the expression of uncertainty in measurement" published by BIMP, IEC, ISO et al.

so there is a wide for for agreements with clients and auditors in relation to specific test methods.

Kind regards
Udo Schlengermann
Agfa NDT GmbH, Huerth, Germany



 
 Reply 
 

Product Spotlight

Ultrasonic Squirter/Gantry System

TecScan’s NDT Ultrasonic Gantry Systems are industrial Squirter scanners designed for non-destru
...
ctive quality testing and raster scanning of large structures and parts. The Gantry Systems are usually composed of an Industrial Mechanical Scanner and a Control Room with System Workstation.
>

FD800 Bench Top Flaw Detectors

The bench-top FD800 flaw detector range combines state-of-the-art flaw detection with advanced mater
...
ial thickness capabilities. Designed for use in the laboratory these gauges are the tool you need for all your flaw detecting needs.
>

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window