where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
813 views
Technical Discussions
David Harvey
David Harvey
00:30 Mar-05-2003
Reflector plate testing

We employ reflector-plate testing on relatively thin (0.090" to 0.500") refractory metals. I would very much like to change to a back - surface reflection moniotoring type of test. Does anyone have any wisdom to contribute to this question? I understand some of the obvious differences, but I am somewhat stymied in coming up with the justification for trying to change over to this test. Thank you for your assistance.


 
 Reply 
 
Ed Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1300

Ed Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1300
01:21 Mar-05-2003
Re: Reflector plate testing
Mr. Harvey:
Could you please provide a bit more information.
I am not clear on what "reflector-plate" testing is.
What are you monitoring or testing for. (Can I assume you are using some form of automated ultrasonic configuration?)
Ed

: We employ reflector-plate testing on relatively thin (0.090" to 0.500") refractory metals. I would very much like to change to a back - surface reflection moniotoring type of test. Does anyone have any wisdom to contribute to this question? I understand some of the obvious differences, but I am somewhat stymied in coming up with the justification for trying to change over to this test. Thank you for your assistance.
.




 
 Reply 
 
Carlos Valdecantos
Engineering
MTORRES, Ing., Spain, Joined May 2001, 9

Carlos Valdecantos

Engineering
MTORRES, Ing.,
Spain,
Joined May 2001
9
09:31 Mar-06-2003
Re: Reflector plate testing
As far as I understand, reflector plate test is also referred to as "double transmission" and gives no information about time of flight (thickness or flaw depth) because the echo being monitored is the one coming from the plate which is kept at a fixed distance from the transducer. Defects are shown in the C-scan as amplitude fall of the plate echo. Axial resolution is not involved, so standard transducer can be used. Although pulse-echo systems are used, reflector plate test is not strictly a pulse-echo test.

True pulse-echo test makes use the backwall echo of the part under test. This gives information on the amplitude (C-scan) and time of flight (D-scan), so thickness of the part and depth of defects are measured. High axial resolution transducers are required for thin parts testing. Also geometric requirements (perpendicularity to the part surface) are more stringent in pulse echo.


C. Valdecantos


 
 Reply 
 

Product Spotlight

Cygnus 6+ PRO Multi-Mode Ultrasonic Thickness Gauge

The Cygnus 6+ PRO thickness gauge is the most advance gauge within the Cygnus range with key featu
...
res including: comprehensive data logging; A-scan and B-scan display; manual gain control; Bluetooth connectivity; and much more. With its unique dual display and three measuring modes (Multiple-Echo, Echo-Echo and Single-Echo), this surface thickness gauge offers maximum versatility for inspections.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

IntraPhase Athena Phased Array System

The Athena Phased Array system, manufactured by WesDyne NDE Products & Technology, consists of a pha
...
sed array acquisition system and PC running IntraSpect software. A PC is used to perform acquisition, analysis and storage of the data. System hardware is capable of operating up to four data sets with any combination of phased array or conventional UT probes. NOW AVAILABLE IN 64-64 CONFIGURATION.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window