where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1565 views
Technical Discussions
Protopappas
Protopappas
03:48 Mar-06-2003
Velocity of stainless steel 316 and plexiglass

Please,

could anyone provide me with the ultrasound velocity of the following materials:
steel 316
plexiglass
perspex (lucite)

I really cannot find accurate values.

Thank you in advance.


 
 Reply 
 
Neil Burleigh
Sales
Krautkramer Australia Pty Ltd, Australia, Joined Dec 2002, 159

Neil Burleigh

Sales
Krautkramer Australia Pty Ltd,
Australia,
Joined Dec 2002
159
00:44 Mar-07-2003
Re: Velocity of stainless steel 316 and plexiglass
: Please,
.
: could anyone provide me with the ultrasound velocity of the following materials:
: steel 316
: plexiglass
: perspex (lucite)
.
: I really cannot find accurate values.
.
: Thank you in advance.
.Here is some info. for you
Lucite Vlong 2680m/sec Vshear 1050m/sec
Plexiglass a)UVA Vlong 2760m/sec Vshear 1090m/sec
b)UVAII Vlong 2730m/sec Vshear 1080m/sec
Hope this helps
Regards



 
 Reply 
 
Uli Mletzko
R & D, Retired
Germany, Joined Nov 1998, 89

Uli Mletzko

R & D, Retired
Germany,
Joined Nov 1998
89
04:24 Mar-07-2003
Re: Velocity of stainless steel 316 and plexiglass

: could anyone provide me with the ultrasound velocity of the following materials:
: steel 316

The ultrasound velocity in stainless steel is strongly depending on the material (cast, forged, weld), especially on the grain size and the grain orientation, leading to anisotropy.
In general, the velocity is lower than in heat treated, forged, fine grain ferritic carbon steel (clong = 5920 m/s, ctrans =3250 m/s).
So, clong = 5800 m/s might be a suitable average value, but sometimes it can be also down to 5400 m/s.
You have to use suitable control specimens or you have calibrate on the test specimen directly.

Regards
Uli Mletzko
NDT Group, MPA
University of Stuttgart, Germany


 
 Reply 
 
Kris Smestad
Kris Smestad
06:46 Mar-14-2003
Re: Velocity of stainless steel 316 and plexiglass
: Please,
.
: could anyone provide me with the ultrasound velocity of the following materials:
: steel 316
: plexiglass
: perspex (lucite)
.
: I really cannot find accurate values.
.
: Thank you in advance.

Keep it simple. If you have a known thickness of a material, you can determine it's exact velocity. Measure a sample with a micrometer. Set your screen range on your A-scan to twice that thickness. After compensating for probe delay, adjust your velocity so you have one signal at 50% and one at 100%.

Easy, right?
.



 
 Reply 
 

Product Spotlight

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window