where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Controle Mesure Systemes
Contrôle Mesure Systèmes designs, develops and manufactures nearly 30 years a complete NDT range of products in eddy current and ultrasonic testing methods.
1875 views
Technical Discussions
terry anson
terry anson
02:18 Feb-06-2001
Selecting a transducer for fruit maturity project

I am working on my senior project at Fresno State. This project
was assigned to me, and I know very little about ultrasound. I
am to use ultrasound to determine if a given fruit is ripe or not.
My main area of concern is in selecting the proper transducer. I
do not want to end up having to buy 4 or 5 different types before
finding one that is suitable. Any help or advice would be
appreciated.
Terry


    
 
 Reply 
 
Dave Utrata
Dave Utrata
02:39 Feb-06-2001
Re: Selecting a transducer for fruit maturity project
I think what you'll have to concern yourself with most is frequency. This sort of work makes us of 500-250 kHz transducers due to attenuation. Beyond that, suitable sample diamter will determine transducer diamter. One tip: low freuency transducers may sometimes be small active elements in a bigger housing, so talk to the manufacturer about this.


: I am working on my senior project at Fresno State. This project
: was assigned to me, and I know very little about ultrasound. I
: am to use ultrasound to determine if a given fruit is ripe or not.
: My main area of concern is in selecting the proper transducer. I
: do not want to end up having to buy 4 or 5 different types before
: finding one that is suitable. Any help or advice would be
: appreciated.
: Terry
.



    
 
 Reply 
 
Rolf Diederichs
Director,
NDT.net, Germany, Joined Nov 1998, 608

Rolf Diederichs

Director,
NDT.net,
Germany,
Joined Nov 1998
608
08:21 Feb-06-2001
Re: Selecting a transducer for fruit maturity project
In September 2000 we had already a similar topic in this forum,
see "ultrasonic propagation in APPLES" http://www.ndt.net/wshop/forum/messages/2103.htm
Dr. Amos Mizrach from the Institute of Agricultural Engineering
posted his opinion.
Contact details can be found at his profile page:
http://www.ndt.net/wshop/profile/profiles/356.htm

Rolf

: I am working on my senior project at Fresno State. This project
: was assigned to me, and I know very little about ultrasound. I
: am to use ultrasound to determine if a given fruit is ripe or not.
: My main area of concern is in selecting the proper transducer. I
: do not want to end up having to buy 4 or 5 different types before
: finding one that is suitable. Any help or advice would be
: appreciated.
: Terry
.



    
 
 Reply 
 
Tom Nelligan
Engineering,
retired, USA, Joined Nov 1998, 390

Tom Nelligan

Engineering,
retired,
USA,
Joined Nov 1998
390
05:27 Feb-06-2001
Re: Selecting a transducer for fruit maturity project
: I am working on my senior project at Fresno State. This project
: was assigned to me, and I know very little about ultrasound. I
: am to use ultrasound to determine if a given fruit is ripe or not.
: My main area of concern is in selecting the proper transducer. I
: do not want to end up having to buy 4 or 5 different types before
: finding one that is suitable. Any help or advice would be
: appreciated.
: Terry
.

Remember that you not only need to select the proper transducer, but also the proper pulser to drive it. Fruits are VERY attenuating as a sound transmission medium compared with the engineering materials that industrial UT equipment is designed for. You will need a pair of low frequency contact transducers (100 to 500 KHz) for a through transmission setup, and a high energy, high gain pulser/receiver to drive the transmitter and amplify the signal from the receiver. We're among the companies that can supply both, if you're interested.

--Tom Nelligan
www.panametrics.com



    
 
 Reply 
 
terry
terry
01:39 Feb-06-2001
Re: Selecting a transducer for fruit maturity project
Thanks for all the help and input. I appreciate it. I looked through
your online catalog. I would prefer an air coupled transducer, but I
was unable to find any low frequency narrowband air coupled tranducers.
Is it wishful thinking on my part to try to find such a trancducer that
would be of use in this type of application?
terry
.
: Remember that you not only need to select the proper transducer, but also the proper pulser to drive it. Fruits are VERY attenuating as a sound transmission medium compared with the engineering materials that industrial UT equipment is designed for. You will need a pair of low frequency contact transducers (100 to 500 KHz) for a through transmission setup, and a high energy, high gain pulser/receiver to drive the transmitter and amplify the signal from the receiver. We're among the companies that can supply both, if you're interested.
.
: --Tom Nelligan
: www.panametrics.com
.



    
 
 Reply 
 
Dipl.-Ing. Martin Heinz
Dipl.-Ing. Martin Heinz
09:12 Feb-07-2001
Re: Selecting a transducer for fruit maturity project
: Thanks for all the help and input. I appreciate it. I looked through
: your online catalog. I would prefer an air coupled transducer, but I
: was unable to find any low frequency narrowband air coupled tranducers.
: Is it wishful thinking on my part to try to find such a trancducer that
: would be of use in this type of application?
: terry
: .
Try contact Mahesh Bhardwaj of Ultran / Secondwave Systems at mcbhardwaj@aol.com. They are specialists in non-contact UT.

Best regards,

Martin Heinz.



    
 
 Reply 
 
Dr. Amos Mizrach
Engineering, R&D
Institute of Agricultural Engineering - The Volcani Center, Israel, Joined Oct 1999, 3

Dr. Amos Mizrach

Engineering, R&D
Institute of Agricultural Engineering - The Volcani Center,
Israel,
Joined Oct 1999
3
00:20 Feb-07-2001
Re: Selecting a transducer for fruit maturity project
The frequency and the power of signal are really the most important parameters for your purposes. You have got good advices by other readers as well. However, don't forget the major actors in that research that are the kind of fruit or vegetable you intend to work with and the path length inside it. For example, potatoes can work with 200 KHz and 40 mm but apples need less than 100 KHz and you will be able to penetrate 5 mm or so. For further information I suggest my article in the Elsevier journal - Ultrasonic 38(2000) 717-722.

Good luck
Dr. Amos Mizrach

: I am working on my senior project at Fresno State. This project
: was assigned to me, and I know very little about ultrasound. I
: am to use ultrasound to determine if a given fruit is ripe or not.
: My main area of concern is in selecting the proper transducer. I
: do not want to end up having to buy 4 or 5 different types before
: finding one that is suitable. Any help or advice would be
: appreciated.
: Terry
.



    
 
 Reply 
 
Rolf Diederichs
Director,
NDT.net, Germany, Joined Nov 1998, 608

Rolf Diederichs

Director,
NDT.net,
Germany,
Joined Nov 1998
608
08:34 Feb-07-2001
Re: Selecting a transducer for fruit maturity project
and a high energy, high gain pulser/receiver to drive the transmitter and amplify the signal from the receiver. We're among the companies that can supply both, if you're interested.
: .
: : --Tom Nelligan
: : www.panametrics.com
: .
.



    
 
 Reply 
 
Rolf Diederichs
Director,
NDT.net, Germany, Joined Nov 1998, 608

Rolf Diederichs

Director,
NDT.net,
Germany,
Joined Nov 1998
608
09:05 Feb-07-2001
Re: Selecting a transducer for fruit maturity project
d velocity measurements. * Food products: A wide variety of tests have been reported, including age
of eggs and potatoes, ripeness of fruits, fat content in beef, and percent of solids in milk. Generally these tests are both
nondestructive and non-contaminating. * Polymerization in plastics ...
http://www.panametrics.com/div_ndt/pages/theory/material.shtml

Regards
Rolf Diederichs

: I'm not sure where you searched.
: You can find via the List of Keywords of the exhibition catalog search
: the following results of companies:
.
: Keyword: transducers
: SEARCH RESULTS: 23
.
: Air-coupled transducers
: SEARCH RESULTS: 7
.



    
 
 Reply 
 
ehsan rouhani
ehsan rouhani
02:31 Mar-01-2002
Re: Selecting a transducer for fruit maturity project
: : Thanks for all the help and input. I appreciate it. I looked through
: : your online catalog. I would prefer an air coupled transducer, but I
: : was unable to find any low frequency narrowband air coupled tranducers.
: : Is it wishful thinking on my part to try to find such a trancducer that
: : would be of use in this type of application?
: : terry
: : .
: Try contact Mahesh Bhardwaj of Ultran / Secondwave Systems at mcbhardwaj@aol.com. They are specialists in non-contact UT.
.
: Best regards,
.
: ehsan rouhani
.



    
 
 Reply 
 

Product Spotlight

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

EKOSCAN Phased Array

In order to always fit your needs, EKOSCAN can manufacture any type of UT transducer, either convent
...
ional or Phased Array. As an ISO 9001: 2015 certified company, EKOSCAN is extremely careful as far a material selection and manufacturing processes are concerned. Our probes guarantee our customers the benefits of latest innovations regarding piezo-composite, backing, impedance adaptation layer, etc. Specific probes for hostile environment: high temperature, high pressure, corrosive environment,etc. Specific probes designed to fit your specific application: optimization of every parameter to guarantee you the best detection.
>

Echomac® Small

Available with up to eight channels of electronics to detect and evaluate thickness, flaws and eccen
...
tricity, this UT tester is housed in a convenient, smaller cabinet. This instrument can be used in conjunction with bubbler or immersion tank systems, or with a test bench or in laboratory applications. The Echomac® Small is available in the FD4, FD6 or FD6A versions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window