where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
4115 views
Technical Discussions
Posma M. Pakpahan
NDT Inspector
PT. Pupuk Kaltim Tbk, Indonesia, Joined Jun 2003, 4

Posma M. Pakpahan

NDT Inspector
PT. Pupuk Kaltim Tbk,
Indonesia,
Joined Jun 2003
4
03:06 Jun-04-2003
Bimetallic Tube Inspection

Dear All,

We have a HP. Stripper in Urea Plant licensed by Snaphrogetti which have tubes made from bimetallic material ( Stainless steel + Zr ). Any of you could inform me the best method to be used to inspect the internal of that tube ? Thank you.


 
 Reply 
 
fabio mussa
Engineering,
SAIPEM SpA, Italy, Joined Dec 2002, 9

fabio mussa

Engineering,
SAIPEM SpA,
Italy,
Joined Dec 2002
9
09:10 Jun-04-2003
Re: Bimetallic Tube Inspection
dear friend
the best solution to inspect bimetallic tubes is by eddy current
try to find some paper on ndt.net


: Dear All,
.
: We have a HP. Stripper in Urea Plant licensed by Snaphrogetti which have tubes made from bimetallic material ( Stainless steel + Zr ). Any of you could inform me the best method to be used to inspect the internal of that tube ? Thank you.
.



 
 Reply 
 
John Hansen
Director, - Eddy Current Technology
ETher NDE Ltd, United Kingdom, Joined Oct 1999, 73

John Hansen

Director, - Eddy Current Technology
ETher NDE Ltd,
United Kingdom,
Joined Oct 1999
73
06:31 Jun-04-2003
Re: Bimetallic Tube Inspection
Hi Fabio

I'm not familair with this tube configuration.

In order to evaluate the possibilty of using any NDT technique there is a lot of information that would be usefull
Internal diameter
Wall thickness of materials (which is on the inside)
Length
Type of defects to be detected and size

My opinion would be that providing you weren't interested in only circumferential cracks or laminations then an eddy current test with a differentail id probe would be the answer (in terms of speed and cost effectivenses) possibly backed up with an IRIS test. However there is a great deal I do not know about your applcation.

Rgds

John Hansen
www.hocking.com


 
 Reply 
 
Rich Roberts
Engineering, Executive Managment
Quest Integrity Group, USA, Joined Nov 1998, 78

Rich Roberts

Engineering, Executive Managment
Quest Integrity Group,
USA,
Joined Nov 1998
78
07:00 Jun-04-2003
Re: Bimetallic Tube Inspection

Dear Posma M. Pakpahan,
Additional information is needed in order to select the proper NDT technique for your specific application. There are many types of tube inspection techniques available (e.g. LOTIS-laser, ET, RFT, MFL, IRIS, etc.) however each technique works differently and is any could possible solve your problem. If you could supply the following information, I believe you could be directed in the right direction:
- Tube Diameter
- Tube Thickness
- Tube Length
- Failure Mechanisms Sought After

Kind Regards,
Rich



 
 Reply 
 
Posma M. Pakpahan
NDT Inspector
PT. Pupuk Kaltim Tbk, Indonesia, Joined Jun 2003, 4

Posma M. Pakpahan

NDT Inspector
PT. Pupuk Kaltim Tbk,
Indonesia,
Joined Jun 2003
4
03:43 Jun-05-2003
Re: Bimetallic Tube Inspection
Dear Friends,

Well, thank you very much for the kindly respond. The details of the tube :
- Material : 25-22-2 Cr/Ni/Mo + Zr
- Dimension : 28.8 mm OD x ( 2.0 mm + 0.7 mm ) Thick
x 5970 mm Length
- Total : 1852 Ea

This equipment is on the new plant with less than 1 yrs operating time and no failures before, the purpose of inspection is to make sure there is no general corrosion or thinning on the inside surface which made from Zr, therefore the result of inspection must be shown the remaining thickness of that Zr material. Thank you.


 
 Reply 
 
Joe Buckley,
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 528

Joe Buckley,

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
528
02:28 Jun-05-2003
Re: Bimetallic Tube Inspection
Based on the assumption that you are looking for thinning of the Zr layer (i.e. quite a small fraction of the total, and are only looking to proove a point (so that a small sample of representative tubes should be adequate) I would suggest that an IRIS technique is likely to be most appropriate.

Joe Buckley

: Dear Friends,
.
: Well, thank you very much for the kindly respond. The details of the tube :
: - Material : 25-22-2 Cr/Ni/Mo + Zr
: - Dimension : 28.8 mm OD x ( 2.0 mm + 0.7 mm ) Thick
: x 5970 mm Length
: - Total : 1852 Ea
.
: This equipment is on the new plant with less than 1 yrs operating time and no failures before, the purpose of inspection is to make sure there is no general corrosion or thinning on the inside surface which made from Zr, therefore the result of inspection must be shown the remaining thickness of that Zr material. Thank you.
.



 
 Reply 
 
Rich Roberts
Engineering, Executive Managment
Quest Integrity Group, USA, Joined Nov 1998, 78

Rich Roberts

Engineering, Executive Managment
Quest Integrity Group,
USA,
Joined Nov 1998
78
04:48 Jun-05-2003
Re: Bimetallic Tube Inspection
Dear Posma M. Pakpahan
Based upon the information provided in your last entry, I believe that either the LOTIS laser process or the IRIS process would be the best solution to your problem. The LOTIS is about twice as fast as the IRIS, however is limited to interior flaws only. Since you appear to only be interested in very small internal erosion, corrosion and pitting the LOTIS can supply you with inspecton test result accuracy’s of +/-0.0508mm (0.002”). Please let me know if you would require additional information on either LOTIS or IRIS.
Kind Regards,
Rich



 
 Reply 
 
fabio mussa
Engineering,
SAIPEM SpA, Italy, Joined Dec 2002, 9

fabio mussa

Engineering,
SAIPEM SpA,
Italy,
Joined Dec 2002
9
06:29 Jun-05-2003
Re: Bimetallic Tube Inspection
Dear friend
Lot of eddy current inspection have been carried out on bimetallic tubes, in order to detect corrosion from inside ( carbamate side) and to detect disbonding between two material.
i think, all eddy current NDT companies, are able to perform this kind of inspection.
Sure with :
Force technologies - denmark
Donegani Anticorrosione - italy

best regards
.



 
 Reply 
 
g l kelkar
g l kelkar
06:10 Nov-27-2003
Re: Bimetallic Tube Inspection

We have recently observed tube seperation in bimetallic tube stripper tube for Urea service. What can be the reason?


 
 Reply 
 
R. Gopal
R. Gopal
07:35 Mar-07-2005
Re: Bimetallic Tube Inspection
Dear Friend:

Zr lined 25-22-2 tubes also encounter the following defects.
1. Zr layer projecting out at bottom side of HP Stripper (indicative of de bonding)
2. Active surface corrosion of 25-22-2 tube Outside dia at projected portions at bottom channel head
2. Active surface attack of 25-22-2 TTS welds which may develop leak in service

(We had serious problem in bimetallic stripper and hence went back to Ti tube bundle again within 2 yrs of operations).

NDT technique whether IRIS Or Eddy Current

It should indicate thickness of both Zr layer & that of 25-22-2 tube within 5% tolerance.
Defects in Zr layer like Wringles, crack, linear opening to be accurately indicated.
TTS welds condition to be assessed by special probes.
Tube sheet overlay 25-22-2 surface corrosion due to "Active" attack to be assessed.

NDT personnel with real authenticity for the above achievemnt of results shall contact me also.

Thanks & regards

R. Gopal


:
Dear All,
.
: We have a HP. Stripper in Urea Plant licensed by Snaphrogetti which have tubes made from bimetallic material ( Stainless steel + Zr ). Any of you could inform me the best method to be used to inspect the internal of that tube ? Thank you.
.



 
 Reply 
 

Product Spotlight

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

32:128PR PAUT & 2-ch TOFD Flaw Detector: SyncScan 2

●32:128PR PAUT with optional 2-ch TOFD to maximize your efficiency ●Support PR mode for corrosi
...
on inspection ●Multiple solutions for welds & corrosion ●Faster scan speed (Approximately 3 meters/minute) ●Light weight: 4kg only including battery
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window