where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

868 views
Technical Discussions
mike macke
NDT Inspector
GE Inspection Services, USA, Joined Aug 2001, 8

mike macke

NDT Inspector
GE Inspection Services,
USA,
Joined Aug 2001
8
02:06 May-05-2003
Measuring Stainless overlay 309L, 347L, 317L,316 etc.

Hello from South Carolina!!! well, once a year I go out to you all for you opinons on the above subject. Is there a system out there that can measure the thickness of Austentic overlay(ferrite)0.8 to 7.8 and it will vary. The welding application can vary also, but it is mostly automated. The backing is SA 285C or 516-70 mild steel (pressure vessels)or SA210 boiler tubes.For UT, the Z's factor is only 2. For magnetic induction or eddy current, the ferrite is the problem. We still measure befor overlay and after. The thickness will range from 1mm to 12mm.

Thankyou
M.C. Macke.


 
 Reply 
 
Doug Breeze
Director, Consultant; R&D
Inspection Software Limited, United Kingdom, Joined May 2000, 20

Doug Breeze

Director, Consultant; R&D
Inspection Software Limited,
United Kingdom,
Joined May 2000
20
08:44 Jun-05-2003
Re: Measuring Stainless overlay 309L, 347L, 317L,316 etc.
In response to Mike Macke's question a few weeks ago Dinsley Devices and Inspection Software have recently installed an automated system to measure Inconel cladding in the bore of 125mm - 300mm carbon steel pipe. Cladding thickness 0mm - 10mm, +/- 0.1mm. Should be suitable for other similar materials.



 
 Reply 
 

Product Spotlight

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Customized Probes and Transducers

With a strong development department and our own piezocomposite production, we accompany you from th
...
e first product idea to serial production. Our scientists are continuously researching new methods in the field of ultrasonic measurement technology. The progress achieved enables us to offer you optimal solutions.
>

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window