where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

GB Inspection Systems Ltd.
A leading UK manufacturer of Ultrasonic Probes, Accessories, Supplier of NDT Equipment and more.
797 views
Technical Discussions
SK AHAMMED ALI
SK AHAMMED ALI
09:43 Oct-14-2014
Atenuation Factor

The “Attenuation Factor C on the test report shall be attained by subtracting1 in.
[25 mm] from the sound-path distance and multiplying the remainder by 2. This factor shall be roundedout to the nearest dB value. Fractional values less than1/2 dB shall be reduced to the lower dB level and thoseof 1/2 dB or greater increased to the higher level.


Can anybody explain this?

    
 
 Reply 
 
Jon Wallis
NDT Inspector, -
Netherlands, Joined Feb 2010, 626

Jon Wallis

NDT Inspector, -
Netherlands,
Joined Feb 2010
626
07:24 Oct-15-2014
Re: Atenuation Factor
In Reply to SK AHAMMED ALI at 09:43 Oct-14-2014 (Opening).

Attenuation is 'absorption' of your sound in a particular material. Some materials attenuate more than others. Think of a light beam in clear dark air (fine grain low alloy carbon steel) and compare this with the same light beam in fog (course grain high alloy carbon steel).
When using the DGS system, you need to compensate for attenuation and specific materials have an attenuation factor that needs to accounted for when UT testing. This is because echo comparison is between a flat bottom hole in fine grain low alloy material (clear air) and your workpiece (unknown). This problem doesn't present itself with side drilled hole based comparisons as the comparison block should be made from the same material as the workpiece.

    
 
 Reply 
 
GOWRISANTHOSH PALIKA
NDT Inspector,
Royscan engineering pte ltd, Singapore, Joined May 2008, 52

GOWRISANTHOSH PALIKA

NDT Inspector,
Royscan engineering pte ltd,
Singapore,
Joined May 2008
52
09:33 Oct-16-2014
Re: Atenuation Factor
In Reply to SK AHAMMED ALI at 09:43 Oct-14-2014 (Opening).

hi
for every inch of sound travelling through the steel, there will be a loss of 2dB. It is correct when you use equipment that all stated in AWS D1.1.

    
 
 Reply 
 

Product Spotlight

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

Lyft™: Pulsed Eddy Current Reinvented

PEC Reinvented—CUI Programs Redefined Corrosion under insulation (CUI) is possibly the greatest u
...
nresolved asset integrity problem in the industry. Current methods for measuring wall thickness with liftoff, without removing insulation, all have severe limitations. Eddyfi introduces Lyft — a reinvented, high-performance pulsed eddy current (PEC) solution. The patent- pending system features a state-of-the-art portable instrument, real- time C-scan imaging, fast data acquisition with grid-mapping and dynamic scanning modes, and flexibility with long cables. It can also scan through thick metal and insulation, as well as aluminum, stainless steel, and galvanized steel weather jackets. Who else but Eddyfi to reinvent an eddy current technique and redefine CUI programs. Got Lyft?
>

YXLON Cougar EVO

Scalable small footprint X-ray inspection systems for assembly and laboratory applications. The
...
YXLON Cougar EVO series was designed to provide the "best-in- class" inspection solutions for SMT, semiconductor, and laboratory assembly applications, while maintaining a small system footprint for maximum convenience. With optimized software and hardware, these systems produce higher quality and more consistent results than other electronics inspection systems currently on the market.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window