where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

Canadian Institute for NDE
We are specialized in training for Radiography, Ultrasonics, Magnetic Particle, Liquid Penetrant, Eddy Current and emerging NDT technologies.
1473 views
Technical Discussions
Arivazhagan
NDT Inspector,
HAL, India, Joined Oct 2014, 5

Arivazhagan

NDT Inspector,
HAL,
India,
Joined Oct 2014
5
10:25 Oct-30-2014
Shear wave reference block for Rings

Need to fabricate a reference standard (Acceptance critereia is 2mm ) for inspecting alumiium ring of size 1200mm OD, 1100mm ID and 90 mm thick , pl suggest.

 
 Reply 
 
Dent
Consultant, NDE Manager NDELevel III/3
NDT Consultant, Canada, Joined Nov 1998, 250

Dent

Consultant, NDE Manager NDELevel III/3
NDT Consultant,
Canada,
Joined Nov 1998
250
12:02 Oct-30-2014
Re: Shear wave reference block for Rings
In Reply to Arivazhagan at 10:25 Oct-30-2014 (Opening).

It is normal to put notches ID & OD on the actual part for this type of inspection rather than make a special cal. block.

Your specification/procedure should be consulted.

 
 Reply 
 
Jawed Akhter
Jawed Akhter
16:23 Oct-30-2014
Re: Shear wave reference block for Rings
In Reply to Arivazhagan at 10:25 Oct-30-2014 (Opening).

Your stansard call for 2mm flat bottom hole of side drill hole ? in eithe case you need
reference block to set up sensitivity.

 
 Reply 
 
Dent
Consultant, NDE Manager NDELevel III/3
NDT Consultant, Canada, Joined Nov 1998, 250

Dent

Consultant, NDE Manager NDELevel III/3
NDT Consultant,
Canada,
Joined Nov 1998
250
21:24 Oct-30-2014
Re: Shear wave reference block for Rings
In Reply to Jawed Akhter at 16:23 Oct-30-2014 .

Subject line of posting is Shear Wave. FBH's are almost always for straight beam. SDH's are normally used for weld inspections.
Notches are used for angle beam examinations of various product forms including large forged rings like you describe. Unless you have additional material to make a cal block from it is common to put the notches in the actual product and if necessary machine them off after testing.

1
 
 Reply 
 
Simon Amallraja
Consultant, Advanced NDT Methods
Anu Consultants, India, Joined Aug 2013, 40

Simon Amallraja

Consultant, Advanced NDT Methods
Anu Consultants,
India,
Joined Aug 2013
40
10:00 Nov-03-2014
Re: Shear wave reference block for Rings
In Reply to Arivazhagan at 10:25 Oct-30-2014 (Opening).

You have couple of Ref Standard manufuacturers with NIST trecebaility.

Check with www.phtools.com. They will be able to support you immediately.

Good Luck

 
 Reply 
 

Product Spotlight

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

Research and Applications Development For NDT

The Research and Applications Development (RAD) group is a newly formed team within Acuren dedicat
...
ed to tackling challenging inspection problems. Our focus is the development of novel, field deployable, advanced inspection techniques for use in cases where standard NDT methods are ineffective. We don't wait for new innovations, we engineer them. From concept to commissioning.
>

Aerospace Systems - Automated Ultrasonic Inspection

USL are specialists in the design and manufacture of turnkey ultrasonic inspection systems for aer
...
ospace applications. From monolithic composites to complex honeycomb structures. This video shows just a few examples of what is possible, find out more at: www.ultrasonic-sciences.co.uk
>

Surf-X® Array Probe

Introducing the Surf-X family of flexible Eddy Current Array (ECA) probes. Featuring unique multiple
...
coil sets and proprietary X-PROBE technology, Surf-X array probes can quickly and accurately handle a range of inspection applications, from inspecting corrosion or cracking in pipes, pressure vessels, or tanks, to assessing and sizing cracks in raised welds and friction stir welds.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window