where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

IMechE Engineering Training Solutions
World leading provider of Non-Destructive Testing and Corrosion Prevention and Coatings training, examinations and Level 3 Consultancy Services

821 views
Technical Discussions
Dave Utrata
R & D,
Center for NDE, Iowa State University, USA, Joined Feb 2000, 37

Dave Utrata

R & D,
Center for NDE, Iowa State University,
USA,
Joined Feb 2000
37
08:01 Jun-20-2003
calibration holes for leak testing

Good Morning all,

Wehave been performing quantitative studies of leak testing using a useful little setup that terminates in an end cap having a hole. We created a number of holes that range from the too-gross (0.03" diameter drilled) to the moderate (0.004" laser drilled) and have been able to document systematic changes in both bubble and acoustic detection, using orifice size, pressure differential, etc. as variables.

The big question: all these holes seem too big compared to the leaks we are asked to chase in real industrial situations. Does anyone have info/ideas on getting small(er) holes for use in our test system? Our next thought is to isolate and capture real leaks into a larger contraption, but that's looking a bit clumsy.

Thanks for your time.


    
 
 
Phil Herman Jr.
Sales, - Manufacture of NDT Reference Standards/Test Blocks
PH Tool Reference Standards, USA, Joined Oct 1999, 79

Phil Herman Jr.

Sales, - Manufacture of NDT Reference Standards/Test Blocks
PH Tool Reference Standards,
USA,
Joined Oct 1999
79
03:28 Jun-20-2003
Re: calibration holes for leak testing
Hello Dave,

PH Tool Reference Standards has machined very small calibration holes for leak testing for tubing mills. Most recent was a series of holes in .028" wall stainless tube. We EDM'd one through-hole per standard, with diameters of .0017, .0039, and .0079". The feedback I recall on the smallest hole was that it was TOO small. Contact me directly for more details.

Best Regards,
Phil Herman Jr.
President/CEO
PH Tool Reference Standards


: Good Morning all,
.
: We have been performing quantitative studies of leak testing using a useful little setup that terminates in an end cap having a hole. We created a number of holes that range from the too-gross (0.03" diameter drilled) to the moderate (0.004" laser drilled) and have been able to document systematic changes in both bubble and acoustic detection, using orifice size, pressure differential, etc. as variables.
.
: The big question: all these holes seem too big compared to the leaks we are asked to chase in real industrial situations. Does anyone have info/ideas on getting small(er) holes for use in our test system? Our next thought is to isolate and capture real leaks into a larger contraption, but that's looking a bit clumsy.
.
: Thanks for your time.
.



    
 
 
James A. Basford
James A. Basford
04:28 Jun-24-2003
Re: calibration holes for leak testing
: Good Morning all,
.
: Wehave been performing quantitative studies of leak testing using a useful little setup that terminates in an end cap having a hole. We created a number of holes that range from the too-gross (0.03" diameter drilled) to the moderate (0.004" laser drilled) and have been able to document systematic changes in both bubble and acoustic detection, using orifice size, pressure differential, etc. as variables.
.
: The big question: all these holes seem too big compared to the leaks we are asked to chase in real industrial situations. Does anyone have info/ideas on getting small(er) holes for use in our test system? Our next thought is to isolate and capture real leaks into a larger contraption, but that's looking a bit clumsy.
.
: Thanks for your time.
.
For many years we have been using 1/16" OD x 0.004" ID tubing welded into demountable flanges as flow restriction elements for calibrated leaks. The smaller gas flow rates needed for our calibrated leaks were obtained by crimping the end of the capillary tubing. Very constant flow rates from 1E-7 to 1E-2 atm cc/sec with gas source pressures from 1 to 20 atm are readily achievable. These are commercially available. I have also
made reliable orifices by drilling #80 holes (0.013" dia) in blind nickel gaskets and swaging them using a punch to get flow rates in the 1E-9 atm cc/sec range. For more information on calibrated leaks and leak testing, visit the web site of the American Vacuum Society, avs.org. Their Recommended Practices documents are be quite useful.


    
 
 
richard collins
richard collins
07:31 Jul-13-2005
Re: calibration holes for leak testing
: : Good Morning all,
Here at H.T.Products ltd we are leak detection specialists and also manufacturers of calibrated reference leaks of all types for most applications.We have a patent on a metal vacuum sintered leak which covers leak rates from typically 10e1 to 10e9 mbarlit/sec. They have the advantage of fast response, can tolerate high pressure differentials and high temperature are available for most gases with calibration traceability to national standards and re-calibration service available.We welcome your enquires.
: .
: : Wehave been performing quantitative studies of leak testing using a useful little setup that terminates in an end cap having a hole. We created a number of holes that range from the too-gross (0.03" diameter drilled) to the moderate (0.004" laser drilled) and have been able to document systematic changes in both bubble and acoustic detection, using orifice size, pressure differential, etc. as variables.
: .
: : The big question: all these holes seem too big compared to the leaks we are asked to chase in real industrial situations. Does anyone have info/ideas on getting small(er) holes for use in our test system? Our next thought is to isolate and capture real leaks into a larger contraption, but that's looking a bit clumsy.
: .
: : Thanks for your time.
: .
: For many years we have been using 1/16" OD x 0.004" ID tubing welded into demountable flanges as flow restriction elements for calibrated leaks. The smaller gas flow rates needed for our calibrated leaks were obtained by crimping the end of the capillary tubing. Very constant flow rates from 1E-7 to 1E-2 atm cc/sec with gas source pressures from 1 to 20 atm are readily achievable. These are commercially available. I have also
: made reliable orifices by drilling #80 holes (0.013" dia) in blind nickel gaskets and swaging them using a punch to get flow rates in the 1E-9 atm cc/sec range. For more information on calibrated leaks and leak testing, visit the web site of the American Vacuum Society, avs.org. Their Recommended Practices documents are be quite useful.
.



    
 
 
richard collins
richard collins
07:34 Jul-13-2005
Re: calibration holes for leak testing
: : Good Morning all,
Here at H.T.Products ltd we are leak detection specialists and also manufacturers of calibrated reference leaks of all types for most applications.We have a patent on a metal vacuum sintered leak which covers leak rates from typically 10e1 to 10e9 mbarlit/sec. They have the advantage of fast response, can tolerate high pressure differentials and high temperature are available for most gases with calibration traceability to national standards and re-calibration service available.We welcome your enquires.
: .



    
 
 

Product Spotlight

Research and Applications Development For NDT

The Research and Applications Development (RAD) group is a newly formed team within Acuren dedicat
...
ed to tackling challenging inspection problems. Our focus is the development of novel, field deployable, advanced inspection techniques for use in cases where standard NDT methods are ineffective. We don't wait for new innovations, we engineer them. From concept to commissioning.
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

High-end Ultrasonic Flaw Detector with 32:128PR PAUT and 2-ch TOFD: SyncScan 2

SIUI’s newly launched SyncScan 2, is a high-end ultrasonic flaw detector with 32:128PR PAUT and
...
2-ch TOFD, which can maximize your efficiency for PA and TOFD. ● Support PA/TOFD/UT ● 32-ch PA is more suitable for inspection on extra-thick wall and high-attenuation material. ● 32-ch PA and 2-ch TOFD work simultaneously. ● Support PR mode for corrosion inspection.
>

High Resolution Industrial CT System for Small/Medium Size Parts Inspection

The YXLON FF35 CT computed tomography system is designed to achieve extremely precise inspection res
...
ults for a wide range of applications. Available in a single or dual tube configuration, it is perfect for very small to medium size parts inspection in the automotive, electronics, aviation, and material science industries.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window