where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

506 views
Technical Discussions
Akshay Singh
Akshay Singh
07:24 Aug-04-2003
PZT film sensing

Hello:

I am using piezo films for sensing cracks in a substrate. I am having problems with dealing with the 60 Hz supply. It is appearing along with its harmonics in the entire frequency spectrum that I am looking at. I shielded the cables with Al foil, covered the film with Al foil but I am still picking up the 60 Hz. I would highly appreciate any suggestions. Regards.. Akshay


 
 Reply 
 
Joerg Schulze-Clewing
Joerg Schulze-Clewing
00:17 Aug-05-2003
Re: PZT film sensing
Dear Akshay,

You'd have to provide some more info about your setup,
such as what frequency range you are using or maybe
which equipment.

Shielding doesn't have much effect at low frequencies
and it is usually better to use coupling transformers
that pass the desired frequency range and isolate
conductive paths. If harmonics are bothering you up
into the frequency range you are using then check for
noise "polluters" on the mains supply. I found one in
our lab yesterday and it was a plain old light dimmer
that had gone bad. It was showing up at several MHz
and after removing it that noise completely vanished.

All the best, Joerg.

----------- Start Original Message -----------
: Hello:
: I am using piezo films for sensing cracks in a substrate. I am having problems with dealing with the 60 Hz supply. It is appearing along with its harmonics in the entire frequency spectrum that I am looking at. I shielded the cables with Al foil, covered the film with Al foil but I am still picking up the 60 Hz. I would highly appreciate any suggestions. Regards.. Akshay
------------ End Original Message ------------





 
 Reply 
 
Akshay Singh
Akshay Singh
07:41 Aug-05-2003
Re: PZT film sensing
Dear Joerg:

Thanks much for the response. You know what? It turned out the surge I was using had a problem with one of the outlet...:-). As soon as I plugged it in a different outlet...BAM...the 60 Hz died. As they say, more than often...the solutions are simple...Thanks again....Akshay

----------- Start Original Message -----------
: Dear Akshay,
: You'd have to provide some more info about your setup,
: such as what frequency range you are using or maybe
: which equipment.
: Shielding doesn't have much effect at low frequencies
: and it is usually better to use coupling transformers
: that pass the desired frequency range and isolate
: conductive paths. If harmonics are bothering you up
: into the frequency range you are using then check for
: noise "polluters" on the mains supply. I found one in
: our lab yesterday and it was a plain old light dimmer
: that had gone bad. It was showing up at several MHz
: and after removing it that noise completely vanished.
: All the best, Joerg.
: : Hello:
: : I am using piezo films for sensing cracks in a substrate. I am having problems with dealing with the 60 Hz supply. It is appearing along with its harmonics in the entire frequency spectrum that I am looking at. I shielded the cables with Al foil, covered the film with Al foil but I am still picking up the 60 Hz. I would highly appreciate any suggestions. Regards.. Akshay
------------ End Original Message ------------




 
 Reply 
 
Joerg Schulze-Clewing
Joerg Schulze-Clewing
01:22 Aug-06-2003
Re: PZT film sensing
Dear Akshay,

Most surge strips contain metal oxyde varistors (MOV) which
are capping the spikes. When they do that they act like
a non-linear devices and create lots of harmonics. But
I'd like to add a word of caution:

If you try several suge strips from different manufacturers
and they all cause this problem that might indicate that
you have some equipment on the line that generates
spikes. Then it may be good to find out what equipment
that is because it can cause damage to lab instruments
that are connected to the line without a surge protector.

I mostly use a little AM radio to find out what causes
spikes or noise.

All the best, Joerg.

----------- Start Original Message -----------
: Dear Joerg:
: Thanks much for the response. You know what? It turned out the surge I was using had a problem with one of the outlet...:-). As soon as I plugged it in a different outlet...BAM...the 60 Hz died. As they say, more than often...the solutions are simple...Thanks again....Akshay
: : Dear Akshay,
: : You'd have to provide some more info about your setup,
: : such as what frequency range you are using or maybe
: : which equipment.
: : Shielding doesn't have much effect at low frequencies
: : and it is usually better to use coupling transformers
: : that pass the desired frequency range and isolate
: : conductive paths. If harmonics are bothering you up
: : into the frequency range you are using then check for
: : noise "polluters" on the mains supply. I found one in
: : our lab yesterday and it was a plain old light dimmer
: : that had gone bad. It was showing up at several MHz
: : and after removing it that noise completely vanished.
: : All the best, Joerg.
: : : Hello:
: : : I am using piezo films for sensing cracks in a substrate. I am having problems with dealing with the 60 Hz supply. It is appearing along with its harmonics in the entire frequency spectrum that I am looking at. I shielded the cables with Al foil, covered the film with Al foil but I am still picking up the 60 Hz. I would highly appreciate any suggestions. Regards.. Akshay
------------ End Original Message ------------




 
 Reply 
 
Ryan Maladen
Ryan Maladen
06:42 Sep-05-2003
Re: PZT film sensing
Dear Akshay/Joerg:
At IIT Delhi we are working on an PZT film sensor which is to be implanted to measure the intracranial pressure of an individual
The problem is we require to measure at a frequency of 1-10 Hz ....with PZT ceramics the same is not possible so cud u give me information regarding the usage of PZT film for my application
Thanks a ton
Looking forward to ur reply
----------- Start Original Message -----------
: Dear Joerg:
: Thanks much for the response. You know what? It turned out the surge I was using had a problem with one of the outlet...:-). As soon as I plugged it in a different outlet...BAM...the 60 Hz died. As they say, more than often...the solutions are simple...Thanks again....Akshay
: : Dear Akshay,
: : You'd have to provide some more info about your setup,
: : such as what frequency range you are using or maybe
: : which equipment.
: : Shielding doesn't have much effect at low frequencies
: : and it is usually better to use coupling transformers
: : that pass the desired frequency range and isolate
: : conductive paths. If harmonics are bothering you up
: : into the frequency range you are using then check for
: : noise "polluters" on the mains supply. I found one in
: : our lab yesterday and it was a plain old light dimmer
: : that had gone bad. It was showing up at several MHz
: : and after removing it that noise completely vanished.
: : All the best, Joerg.
: : : Hello:
: : : I am using piezo films for sensing cracks in a substrate. I am having problems with dealing with the 60 Hz supply. It is appearing along with its harmonics in the entire frequency spectrum that I am looking at. I shielded the cables with Al foil, covered the film with Al foil but I am still picking up the 60 Hz. I would highly appreciate any suggestions. Regards.. Akshay
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

NDT.net launches mobile-friendly design

NDT.net has revamped its website providing a mobile-friendly design.The front page received a comp
...
letely new design and all other sections are now reacting responsively on mobile devices. This has been a major step to make our website more user- friendly.
>

MUSE Mobile Ultrasonic Equipment

The MUSE, a portable ultrasonic imaging system, was developed for in-field inspections of light-weig
...
ht structures. The MUSE consists of a motor-driven manipulator, a water circulation system for the acoustic coupling and a portable ultrasonic flaw detector (USPC 3010). The MUSE provides images of internal defects (A-, B-,C- and D-scan).
>

PAUT Probes

Typical Phased Array probes have frequencies between 1MHz and 20MHz and the number of wafers is 10
...
to 128. M2 Electronics offers customers conventionally ultrasound probes and the ability to provide high-precision Phased Array Ultrasound Probes of up to 256 wafers. We can also customize the probe for our customers to meet the specific application requirements of the user.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window