where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

ACS-Solutions GmbH
1059 views
Technical Discussions
Josip Vuk
Josip Vuk
01:52 Sep-08-2003
Aircraft weld incpection

I am a student at Faculty of Engineering and Naval Arhitecture in Zagreb. I am doing my final thesis and am looking for a Maintenance Manual or Component Repair and Overhaul Manual for any part of any type of any Boeing or Airbus aircraft, which defines inspection of welds (either steel or aluminum).
My intention is to simulate such a part in faculty`s labaratory (for I am unable to acquire a real-life part or documentation)and to perform prescribed radiografic (or ultrasonic) testing.
Materials can be on-line.


 
 Reply 
 
Joe Buckley
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 526

Joe Buckley

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
526
06:50 Sep-08-2003
Re: Aircraft weld incpection
in my experience there are very few critical welded joints in Aircraft structures. Mostly just used in ancilliary assemblies, In particular in Ducting (e.g thin wall stainless or alloy tubes) and in landing gear.

----------- Start Original Message -----------
: I am a student at Faculty of Engineering and Naval Arhitecture in Zagreb. I am doing my final thesis and am looking for a Maintenance Manual or Component Repair and Overhaul Manual for any part of any type of any Boeing or Airbus aircraft, which defines inspection of welds (either steel or aluminum).
: My intention is to simulate such a part in faculty`s labaratory (for I am unable to acquire a real-life part or documentation)and to perform prescribed radiografic (or ultrasonic) testing.
: Materials can be on-line.
------------ End Original Message ------------




 
 Reply 
 
Gary
Consultant
TWI, United Kingdom, Joined May 2001, 15

Gary

Consultant
TWI,
United Kingdom,
Joined May 2001
15
02:31 Sep-11-2003
Re: Aircraft weld incpection
From my experience I have seen some fairly bad accidents through failures of welds in ductings, particularly with secondary damge to wiring looms etc.

Landing gear also has its uses on occassion.

----------- Start Original Message -----------
: in my experience there are very few critical welded joints in Aircraft structures. Mostly just used in ancilliary assemblies, In particular in Ducting (e.g thin wall stainless or alloy tubes) and in landing gear.
: : I am a student at Faculty of Engineering and Naval Arhitecture in Zagreb. I am doing my final thesis and am looking for a Maintenance Manual or Component Repair and Overhaul Manual for any part of any type of any Boeing or Airbus aircraft, which defines inspection of welds (either steel or aluminum).
: : My intention is to simulate such a part in faculty`s labaratory (for I am unable to acquire a real-life part or documentation)and to perform prescribed radiografic (or ultrasonic) testing.
: : Materials can be on-line.
------------ End Original Message ------------




 
 Reply 
 
Carlos Valdecantos
Engineering
MTORRES, Ing., Spain, Joined May 2001, 9

Carlos Valdecantos

Engineering
MTORRES, Ing.,
Spain,
Joined May 2001
9
01:07 Sep-12-2003
Re: Aircraft weld incpection
AIRBUS is currently using welded stringers as an alternative to massive machinning of thick plates. Welding is carried out by high power laser.

Our company is the supplier of the automatic machines for this process. Please, refer to MTORRES web site.

Regards,

C. Valdecantos



 
 Reply 
 

Product Spotlight

GUL QSR1® Scanning

How do you measure pipe wall thickness without direct access to the area? QSR® Scanning - Guide Wav
...
e Quantitative Short Range Scanning.
>

NEW Wheel Type Phased Array Probe

DOPPLER NEW Wheel Type Phased Array Probe, more stable, new tyre makes lesser acoustic attenuation
...
, much lighter makes easier to handle, more slim size, magnetic and mechanical encoder optional etc...more
>

Robotic laser shearography enables 100% inspection of complex, flight-critical composite structures

An article in “Composites World Magazine” showcases Non Destructive Testing of aero-structures
...
with Laser Shearography. Over the years Dantec Dynamics has supplied many solutions for the aerospace industry. Referring to specific customer projects several of these cases are examined to outline the advantages of using Laser Shearography for automated defect detection.
>

Aerospace Systems - Automated Ultrasonic Inspection

USL are specialists in the design and manufacture of turnkey ultrasonic inspection systems for aer
...
ospace applications. From monolithic composites to complex honeycomb structures. This video shows just a few examples of what is possible, find out more at: www.ultrasonic-sciences.co.uk
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window