where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

GB Inspection Systems Ltd.
A leading UK manufacturer of Ultrasonic Probes, Accessories, Supplier of NDT Equipment and more.
1057 views
Technical Discussions
Josip Vuk
Josip Vuk
01:52 Sep-08-2003
Aircraft weld incpection

I am a student at Faculty of Engineering and Naval Arhitecture in Zagreb. I am doing my final thesis and am looking for a Maintenance Manual or Component Repair and Overhaul Manual for any part of any type of any Boeing or Airbus aircraft, which defines inspection of welds (either steel or aluminum).
My intention is to simulate such a part in faculty`s labaratory (for I am unable to acquire a real-life part or documentation)and to perform prescribed radiografic (or ultrasonic) testing.
Materials can be on-line.


 
 Reply 
 
Joe Buckley
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 526

Joe Buckley

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
526
06:50 Sep-08-2003
Re: Aircraft weld incpection
in my experience there are very few critical welded joints in Aircraft structures. Mostly just used in ancilliary assemblies, In particular in Ducting (e.g thin wall stainless or alloy tubes) and in landing gear.

----------- Start Original Message -----------
: I am a student at Faculty of Engineering and Naval Arhitecture in Zagreb. I am doing my final thesis and am looking for a Maintenance Manual or Component Repair and Overhaul Manual for any part of any type of any Boeing or Airbus aircraft, which defines inspection of welds (either steel or aluminum).
: My intention is to simulate such a part in faculty`s labaratory (for I am unable to acquire a real-life part or documentation)and to perform prescribed radiografic (or ultrasonic) testing.
: Materials can be on-line.
------------ End Original Message ------------




 
 Reply 
 
Gary
Consultant
TWI, United Kingdom, Joined May 2001, 15

Gary

Consultant
TWI,
United Kingdom,
Joined May 2001
15
02:31 Sep-11-2003
Re: Aircraft weld incpection
From my experience I have seen some fairly bad accidents through failures of welds in ductings, particularly with secondary damge to wiring looms etc.

Landing gear also has its uses on occassion.

----------- Start Original Message -----------
: in my experience there are very few critical welded joints in Aircraft structures. Mostly just used in ancilliary assemblies, In particular in Ducting (e.g thin wall stainless or alloy tubes) and in landing gear.
: : I am a student at Faculty of Engineering and Naval Arhitecture in Zagreb. I am doing my final thesis and am looking for a Maintenance Manual or Component Repair and Overhaul Manual for any part of any type of any Boeing or Airbus aircraft, which defines inspection of welds (either steel or aluminum).
: : My intention is to simulate such a part in faculty`s labaratory (for I am unable to acquire a real-life part or documentation)and to perform prescribed radiografic (or ultrasonic) testing.
: : Materials can be on-line.
------------ End Original Message ------------




 
 Reply 
 
Carlos Valdecantos
Engineering
MTORRES, Ing., Spain, Joined May 2001, 9

Carlos Valdecantos

Engineering
MTORRES, Ing.,
Spain,
Joined May 2001
9
01:07 Sep-12-2003
Re: Aircraft weld incpection
AIRBUS is currently using welded stringers as an alternative to massive machinning of thick plates. Welding is carried out by high power laser.

Our company is the supplier of the automatic machines for this process. Please, refer to MTORRES web site.

Regards,

C. Valdecantos



 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Varex Imaging Large Field of View (FOV) Digital Detector Arrays (DDAs)

A larger FOV DDA can reduce the space and volume of the X-ray inspection system on the factory floor
...
, enable faster scanning times, better throughput and better resolution images at a lower dose. Customers can also save time and money. With these benefits in mind, Varex Imaging has designed a family of large FOV detectors (4343HE, XRD 1611, 4343DX-I, 4343CT) for our industrial imaging customers.
>

TraiNDE UT

TraiNDE UT is a virtual tool associated with a signal database which simulates real inspection con
...
ditions for numerous applications (Type A/V1 block, DAC block, welds and plates).
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window