where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
454 views
Technical Discussions
Bijay Muduli
Engineering
IOCL, India, Joined Jul 2003, 4

Bijay Muduli

Engineering
IOCL,
India,
Joined Jul 2003
4
08:40 Oct-10-2003
Ultrasonics for Cement Lining

1) Is there any Ultrasonic technique to measure lining/ coating thickness on steel pipes?

2) Can dual probes help in this regard?

Your valuable replies shall be appreciated.

Regards



 
 Reply 
 
Todd Allen
Consultant, Ground Penetrating Radar ( GPR )
Radarview Concrete and Underground 3D Imaging, USA, Joined Jan 2003, 7

Todd Allen

Consultant, Ground Penetrating Radar ( GPR )
Radarview Concrete and Underground 3D Imaging,
USA,
Joined Jan 2003
7
01:41 Oct-13-2003
Re: Ultrasonics for Cement Lining
----------- Start Original Message -----------
: 1) Is there any Ultrasonic technique to measure lining/ coating thickness on steel pipes?
: 2) Can dual probes help in this regard?
: Your valuable replies shall be appreciated.
: Regards
------------ End Original Message ------------

Hello,

Yes, there are a few methods that could be used to measure the thickness of concrete / cement linings and or coatings. The 1st is Ground Penetrating Radar which will measure the thickness of the concrete by detecting the strong dielectric change at the concrete-steel interface. This method must be done from the concrete side not the steel side.
The 2nd method is Impact Echo testing which essentially uses very low frequency impacts on the concrete surface. The frequency response from the echo at the interface can be correlated to a thickness.
The 3rd method would be to use Radiography to get a profile image of the pipe. This method may/may not work depending on the size and thickness of the pipe and concrete.

Thanks,
Todd Allen
Radarview Structural and Underground Services
281-705-9476


 
 Reply 
 
Bijay Muduli
Engineering
IOCL, India, Joined Jul 2003, 4

Bijay Muduli

Engineering
IOCL,
India,
Joined Jul 2003
4
02:08 Oct-16-2003
Re: Ultrasonics for Cement Lining
----------- Start Original Message -----------
: : 1) Is there any Ultrasonic technique to measure lining/ coating thickness on steel pipes?
: : 2) Can dual probes help in this regard?
: : Your valuable replies shall be appreciated.
: : Regards
: Hello,
: Yes, there are a few methods that could be used to measure the thickness of concrete / cement linings and or coatings. The 1st is Ground Penetrating Radar which will measure the thickness of the concrete by detecting the strong dielectric change at the concrete-steel interface. This method must be done from the concrete side not the steel side.
: The 2nd method is Impact Echo testing which essentially uses very low frequency impacts on the concrete surface. The frequency response from the echo at the interface can be correlated to a thickness.
: The 3rd method would be to use Radiography to get a profile image of the pipe. This method may/may not work depending on the size and thickness of the pipe and concrete.
: Thanks,
: Todd Allen
: Radarview Structural and Underground Services
: 281-705-9476
------------ End Original Message ------------

Thank you verymuch Mr Allen.




 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

NDTkit RT

NDTkit RT, TESTIA's Digital Radiography software The NDTkit product line software for X-ray analysi
...
s. NDTkit RT is a software benefiting from the Ultis kernel which is dedicated to radiographic image analysis. It offers a set of tools and filtering processes to assist RT operators in finding relevant flaws.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window