where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
445 views
Technical Discussions
Bijay Muduli
Engineering
IOCL, India, Joined Jul 2003, 4

Bijay Muduli

Engineering
IOCL,
India,
Joined Jul 2003
4
08:40 Oct-10-2003
Ultrasonics for Cement Lining

1) Is there any Ultrasonic technique to measure lining/ coating thickness on steel pipes?

2) Can dual probes help in this regard?

Your valuable replies shall be appreciated.

Regards



    
 
 Reply 
 
Todd Allen
Consultant, Ground Penetrating Radar ( GPR )
Radarview Concrete and Underground 3D Imaging, USA, Joined Jan 2003, 7

Todd Allen

Consultant, Ground Penetrating Radar ( GPR )
Radarview Concrete and Underground 3D Imaging,
USA,
Joined Jan 2003
7
01:41 Oct-13-2003
Re: Ultrasonics for Cement Lining
----------- Start Original Message -----------
: 1) Is there any Ultrasonic technique to measure lining/ coating thickness on steel pipes?
: 2) Can dual probes help in this regard?
: Your valuable replies shall be appreciated.
: Regards
------------ End Original Message ------------

Hello,

Yes, there are a few methods that could be used to measure the thickness of concrete / cement linings and or coatings. The 1st is Ground Penetrating Radar which will measure the thickness of the concrete by detecting the strong dielectric change at the concrete-steel interface. This method must be done from the concrete side not the steel side.
The 2nd method is Impact Echo testing which essentially uses very low frequency impacts on the concrete surface. The frequency response from the echo at the interface can be correlated to a thickness.
The 3rd method would be to use Radiography to get a profile image of the pipe. This method may/may not work depending on the size and thickness of the pipe and concrete.

Thanks,
Todd Allen
Radarview Structural and Underground Services
281-705-9476


    
 
 Reply 
 
Bijay Muduli
Engineering
IOCL, India, Joined Jul 2003, 4

Bijay Muduli

Engineering
IOCL,
India,
Joined Jul 2003
4
02:08 Oct-16-2003
Re: Ultrasonics for Cement Lining
----------- Start Original Message -----------
: : 1) Is there any Ultrasonic technique to measure lining/ coating thickness on steel pipes?
: : 2) Can dual probes help in this regard?
: : Your valuable replies shall be appreciated.
: : Regards
: Hello,
: Yes, there are a few methods that could be used to measure the thickness of concrete / cement linings and or coatings. The 1st is Ground Penetrating Radar which will measure the thickness of the concrete by detecting the strong dielectric change at the concrete-steel interface. This method must be done from the concrete side not the steel side.
: The 2nd method is Impact Echo testing which essentially uses very low frequency impacts on the concrete surface. The frequency response from the echo at the interface can be correlated to a thickness.
: The 3rd method would be to use Radiography to get a profile image of the pipe. This method may/may not work depending on the size and thickness of the pipe and concrete.
: Thanks,
: Todd Allen
: Radarview Structural and Underground Services
: 281-705-9476
------------ End Original Message ------------

Thank you verymuch Mr Allen.




    
 
 Reply 
 

Product Spotlight

NEW! The PragmaPro Instrument Platform

The PragmaPro is based on a modular cartridge technology and supports various NDT instrument modal
...
ities such as UT, PAUT, ECT and many more. This new platform is based on a machined, powder-coated aluminum frame for shock-proofness, best sealing qualities and maximum heat dissipation. This is practical to extend the outdoor temperature range and/or to extend the power injected in the transducers. The PragmaPro is aiming at a very wide range of applications, such as weld scanning, corrosion mapping and composite testing.
>

High-end Ultrasonic Flaw Detector with 32:128PR PAUT and 2-ch TOFD: SyncScan 2

SIUI’s newly launched SyncScan 2, is a high-end ultrasonic flaw detector with 32:128PR PAUT and
...
2-ch TOFD, which can maximize your efficiency for PA and TOFD. ● Support PA/TOFD/UT ● 32-ch PA is more suitable for inspection on extra-thick wall and high-attenuation material. ● 32-ch PA and 2-ch TOFD work simultaneously. ● Support PR mode for corrosion inspection.
>

CIVA 2017 UT Module

CIVA NDE Simulation Software is the world leader of NDT Simulation. The UT simulation Module incl
...
udes: - "Beam computation": Beam propagation simulation - "Inspection Simulation": Beam interaction with flaws or specimens The user can simulate a whole inspection process (pulse echo, tandem or TOFD) with a wide range of probes (conventional, Phased- arrays or EMAT), components, and flaws.
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window