where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

2807 views
Technical Discussions
Manoj
NDT Inspector, NDT Technician
India, Joined Feb 2010, 12

Manoj

NDT Inspector, NDT Technician
India,
Joined Feb 2010
12
10:02 Apr-27-2013
MFL corrosion mapping

I am using Silverwing VS2i for (MFL)bottom floor corrosion mapping. Actually I have been faced some difficulty to do the scan on FRP coated bottom floor of the tank. As per the setting procedure I got only 1 mm sensor lift off. (Plate thickness was10 mm. FRP coat thickness was 6 mm). Generally almost of the tank bottom floor plates are appearing uneven and undulated surface.. Especially in this specific case the bottom floor has been coat lining and patch works also. There were enough chance to hit the sensor on the floor surface and getting false indications, There were no possibilities to prove up the mfl indications by manual UT.

I have to do one more tank mfl in the same condition. Please let me know have any amicable solution or suggestion for overcoming these things? How can I maintain the sensitivity and quality of the job?

Thanks in advance for all valuable suggestions.

Manoj

 
 Reply 
 
Bounatiro
NDT Inspector, QAQC
Csc- exp, Algeria, Joined Sep 2011, 58

Bounatiro

NDT Inspector, QAQC
Csc- exp,
Algeria,
Joined Sep 2011
58
22:29 Apr-08-2014
Re: MFL corrosion mapping
In Reply to Manoj at 10:02 Apr-27-2013 (Opening).

Mr Manoj

I have the same problem as you, i will do inspection next month for bottom of 9 mm thickness and 4mm FRP.
How did you do it

 
 Reply 
 
Manoj
Manoj
11:39 Apr-09-2014
Re: MFL corrosion mapping
In Reply to Bounatiro at 22:29 Apr-08-2014 .

Mr.Bounatiro

I used to VS2! Scanner, but now the new 3D version is available it can achieve at least 2mm sensor lift off in the same condition. It will be achieve little more gaps between the floor and sensor head. Manual UT proves up is impossible so you clearly communicate with the client regarding the limitations of technology. The hand scanner use to cover the maximum area of the floor. Confirm the floor preparation is enough to do execute the job and offer to them maximum coverage and accuracy as possible.

It’s really a challenging task, wish you all success.


 
 Reply 
 
gopi
Engineering, NDT Engineer
seeking long & Short term job - Freelancer, India, Joined Jun 2012, 26

gopi

Engineering, NDT Engineer
seeking long & Short term job - Freelancer,
India,
Joined Jun 2012
26
12:13 Apr-09-2014
Re: MFL corrosion mapping
In Reply to Manoj at 10:02 Apr-27-2013 (Opening).

Mr. Manoj,

For those type of jobs, proper cleaning is needed, and yellow shims are necessary, they give us the proper height, for further details u can read the settings mentioned on the equipment itself.



gopi

 
 Reply 
 
Thiru NDT Level III, Singapore
Engineering,
Singapore, Joined Mar 2013, 1

Thiru NDT Level III, Singapore

Engineering,
Singapore,
Joined Mar 2013
1
12:54 Sep-30-2015
Re: MFL corrosion mapping
In Reply to gopi at 12:13 Apr-09-2014 .

Hi,
I would like to hear your experience with scanning of bottom plates over FRP. Do let me know how comfortable you are with Silverwing Equipment?
Who are the MFL equipment manufacturers available in market?
Thanks

Thiru

 
 Reply 
 

Product Spotlight

MANTIS

MANTIS is a compact, powerful and affordable flaw detector (16:64PR), dedicated to field operators
...
. This portable equipment offers standard (electronic-, sector-, compound scan, conventional UT for pulse-echo, dual array and TOFD inspections), and advanced phased-array (real-time TFM -Total Focusing Method). MANTIS benefits from the same intuitive and user-friendly interface (CAPTURE) than Gekko for easier inspections.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Ultrasonic Probe Recharacterization Service

NDT Systems offers a comprehensive Aftercare and Recharacterization Service for all our ultrasonic
...
probes. The Recharacterization Service is fully compliant with International ASTM E1065 Standard Guide (and other applicable standards) and offers complete documentation, traceable to the ASTM E1065 Standard. For more details or to schedule Recharacterization Services contact ndtsales@ndtsystems.com
>

Combination of Digital Image Correlation and Thermographic Measurements

The combination of measuring results from the digital image correlation (ARAMIS, DIC) and temperat
...
ure measuring data from infrared cameras permits the simultaneous analysis of the thermal and mechanical behavior of test specimens in the materials and components testing field.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window