where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1819 views
Technical Discussions
vivek
India, Joined Dec 2015, 5

vivek

India,
Joined Dec 2015
5
04:45 Jan-02-2016
UT OF PIPING ABOVE 20 INCHES

Dear Experts,

happy new year,

i have a doubt, we have to do UT on pipe 24'',12.70 mm size. we have a calibration block of 36'', 12.70 mm size. can we use this calibration block as a reference block?

 
 Reply 
 
Andreas
NDT Inspector, Specially in the oilfield
Tuboscope Vetco(Deutschland)Gmbh, Germany, Joined Oct 1999, 131

Andreas

NDT Inspector, Specially in the oilfield
Tuboscope Vetco(Deutschland)Gmbh,
Germany,
Joined Oct 1999
131
08:27 Jan-02-2016
Re: UT OF PIPING ABOVE 20 INCHES
In Reply to vivek at 04:45 Jan-02-2016 (Opening).

Hallo Vivek,
you must more specific.
If you check for transverse defects only , it should be not a problem, because it is the same wall thickness.

Then what is the requirement of the specification you are using.


Regards

Andreas

 
 Reply 
 
vivek
India, Joined Dec 2015, 5

vivek

India,
Joined Dec 2015
5
10:04 Jan-02-2016
Re: UT OF PIPING ABOVE 20 INCHES
In Reply to Andreas at 08:27 Jan-02-2016 .

Mr. Andreas,

we are doing UT as per SEC V and our acceptance criteria is B31.3.

 
 Reply 
 
Diego
Consultant,
Freelance, Spain, Joined May 2013, 201

Diego

Consultant,
Freelance,
Spain,
Joined May 2013
201
14:00 Jan-02-2016
Re: UT OF PIPING ABOVE 20 INCHES
In Reply to vivek at 04:45 Jan-02-2016 (Opening).

Hi Vivek
It is right if T-434.1.2, T-434.1.5 and T-434.1.6 are fulfiled. If T-434.1.5 is not fulfiled , then ASME B31.3, 344.6.1 may be used.

 
 Reply 
 
vivek
India, Joined Dec 2015, 5

vivek

India,
Joined Dec 2015
5
15:05 Jan-02-2016
Re: UT OF PIPING ABOVE 20 INCHES
In Reply to Diego at 14:00 Jan-02-2016 .

Dear Mr. Diego,

the requirements of T-434.1.2, T-434.1.5 and T-434.1.6 are fulfilled.

my doubt is about T-434.1.7.1. which says-- for examination in materials where examination surface diameter is greater than 20''(500 mm), a block of essentially same curvature, or alternatively, a flat basic calibration block, may be used.

is it means that i shall use same curvature or flat block?
or i can used any block which is above 20'' in diameter and fulfills the requirements of T- 434.3.?

 
 Reply 
 
Diego
Consultant,
Freelance, Spain, Joined May 2013, 201

Diego

Consultant,
Freelance,
Spain,
Joined May 2013
201
17:38 Jan-02-2016
Re: UT OF PIPING ABOVE 20 INCHES
In Reply to vivek at 15:05 Jan-02-2016 .

Mr. Vivek.
In accordance with T-434.3, I think that it is permittede to employ a flat block.

 
 Reply 
 
Diego
Consultant,
Freelance, Spain, Joined May 2013, 201

Diego

Consultant,
Freelance,
Spain,
Joined May 2013
201
17:56 Jan-02-2016
Re: UT OF PIPING ABOVE 20 INCHES
In Reply to Diego at 17:38 Jan-02-2016 .

Mr. Vivek.
Further to my previous post. I see no objection to use the calibration block of 36" as reference block also

 
 Reply 
 
Collin Maloney
NDT Inspector, - Plant Inspector
Applus RTD, Australia, Joined Nov 2000, 147

Collin Maloney

NDT Inspector, - Plant Inspector
Applus RTD,
Australia,
Joined Nov 2000
147
09:42 Jan-03-2016
Re: UT OF PIPING ABOVE 20 INCHES
In Reply to vivek at 15:05 Jan-02-2016 .

Hi Vivek
T434.1.7 means that you can use either one. A curved block "or" a flat block, your choice

 
 Reply 
 

Product Spotlight

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Conformable wedge transducer

The conformability is obtained with a flexible membrane filled with water between the transducer and
...
the inspected component. The coupling between the membrane and the component requires a small quantity of water or couplant. The conformable wedge combines the acoustic performance of immersion technique with good coupling and low attenuation.
>

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

High-performance Linear Phased Array Probes

Available to order from stock in a range of 5MHz – 7.5MHz and from 16 to 64 elements. Designed w
...
ith piezo-composite elements, Phoenix phased array probes provide high-resolution imaging to maximise sensitivity; accurate ultrasonic detection and sizing of defects in welds; and effective corrosion mapping. Housed in a rugged stainless steel case for on-site industrial NDT applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window