where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1051 views
Technical Discussions
vengadesh
Engineering,
Tech Mahindra LTD, India, Joined Mar 2016, 4

vengadesh

Engineering,
Tech Mahindra LTD,
India,
Joined Mar 2016
4
13:03 Mar-29-2016
probe output

Dear sir,
I have one doubt ,please help. we have 60 degree probe the prespex shoe was thickness reduced, due to continuous friction . the output of probe wavelength was changed into 65 degree. how can i draw DAC.? for that what is the formula for that..?

 
 Reply 
 
joan pagnoul
Student,
Technifutur, Belgium, Joined Mar 2014, 7

joan pagnoul

Student,
Technifutur,
Belgium,
Joined Mar 2014
7
15:19 Mar-29-2016
Re: probe output
In Reply to vengadesh at 13:03 Mar-29-2016 (Opening).

I think that first, your probe is useless because if I remember norms says 60+/-2 degrees.
And to draw a DAC, methods never change and there is no formula

1
 
 Reply 
 
Csaba Hollo
,
Retired, Canada, Joined Feb 2010, 301

Csaba Hollo

,
Retired,
Canada,
Joined Feb 2010
301
23:29 Mar-29-2016
Re: probe output
In Reply to vengadesh at 13:03 Mar-29-2016 (Opening).

If the code allows you to work with an angle outside of the 60 degree+-, then your calibrations, including regenerating your DAC, must be redone.
Several things have changed, not just your angle, but also your index point and most likely sensitivity.

1
 
 Reply 
 
massimo carminati
Consultant, AUT specialist
IMG Ultrasuoni Srl, Italy, Joined Apr 2007, 691

massimo carminati

Consultant, AUT specialist
IMG Ultrasuoni Srl,
Italy,
Joined Apr 2007
691
19:37 Mar-30-2016
Re: probe output
In Reply to vengadesh at 13:03 Mar-29-2016 (Opening).

Most codes would not allow you to use such a drifted angle from standard. You should recondition the probe or the wedge by adding a new wear sole, but before that you should bring back the original wedge angle to the original value. I warmly not suggest to just use sand paper for doing this.

 
 Reply 
 

Product Spotlight

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

Research Center IDEKO develops an ultrasonic train wheel inspection system for CAF

The Basque Research centre IK4-IDEKO has developed a state-of-the-art ultrasonic inspection system f
...
or the train wheel. This system secures a sound condition of train wheels and is thus a significant contribution to rail transport safety. The device was delivered to CAF recently and its use allows the manufacturer to become an approved supplier of rolling stock in Italy, as it meets the demanding homologation standards of this country. \\\\r\\\\n
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window