where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

YXLON International GmbH
YXLON International - innovative High-Tech-Company with long traditionYXLON International develops, manufactures and markets digital radios ...
695 views
Technical Discussions
Matt McCormick
Matt McCormick
07:13 Feb-04-2004
NDT for car headlight adhesive failure

I'm trying to find out a good method for which to scan a section of a headlight where the lens is glued to the plastic housing in order to find either delaminations of the adhesive or areas where there is not enough adhesive. Ideally I would want something that could be done on the assembly line. I've looked at dry coupling ultrasound, microwaves, and something called ultrafluorescence (which I don't think will work for us, because our adhesive is not UV cured). Which of these do you think would give me the best results, and which do you think we could do in-line? Also, might there be something else out there that might work better than the methods I've listed? Any thoughts would be very helpful.


 
 Reply 
 
Phil Thayer
Phil Thayer
00:22 Feb-04-2004
Re: NDT for car headlight adhesive failure
----------- Start Original Message -----------
: I'm trying to find out a good method for which to scan a section of a headlight where the lens is glued to the plastic housing in order to find either delaminations of the adhesive or areas where there is not enough adhesive. Ideally I would want something that could be done on the assembly line. I've looked at dry coupling ultrasound, microwaves, and something called ultrafluorescence (which I don't think will work for us, because our adhesive is not UV cured). Which of these do you think would give me the best results, and which do you think we could do in-line? Also, might there be something else out there that might work better than the methods I've listed? Any thoughts would be very helpful.
------------ End Original Message ------------


Was the dry coupled UT sucessful from an inspection stand point? I would think it would be, then you could address the on-line aspect. Is there a problem with the part getting wet (water, alcohol)? We have come up with solutions for many on-line UT bond inspection problems.

Phil
NDTA 609-716-4051



 
 Reply 
 
Ethan
Ethan
06:17 Feb-05-2004
Re: NDT for car headlight adhesive failure
Hi,

If this is a clear lens that is being bonded, wouldn't that change it's light reflectivity and therfore use a simple laser technique?

regards
e

----------- Start Original Message -----------
: : I'm trying to find out a good method for which to scan a section of a headlight where the lens is glued to the plastic housing in order to find either delaminations of the adhesive or areas where there is not enough adhesive. Ideally I would want something that could be done on the assembly line. I've looked at dry coupling ultrasound, microwaves, and something called ultrafluorescence (which I don't think will work for us, because our adhesive is not UV cured). Which of these do you think would give me the best results, and which do you think we could do in-line? Also, might there be something else out there that might work better than the methods I've listed? Any thoughts would be very helpful.
:
: Was the dry coupled UT sucessful from an inspection stand point? I would think it would be, then you could address the on-line aspect. Is there a problem with the part getting wet (water, alcohol)? We have come up with solutions for many on-line UT bond inspection problems.
: Phil
: NDTA 609-716-4051
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Aerospace Systems - Automated Ultrasonic Inspection

USL are specialists in the design and manufacture of turnkey ultrasonic inspection systems for aer
...
ospace applications. From monolithic composites to complex honeycomb structures. This video shows just a few examples of what is possible, find out more at: www.ultrasonic-sciences.co.uk
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

iProbe - USB Phased Array Probe

Turn your PC, Laptop or Tablet into a powerful 32:64 Phased Array system with our USB powered Phas
...
ed Array iProbe and inspection software package. Perform affordable weld inspection and corrosion mapping inspections with this powerful but small system. The probe has a 100V pulser, 8K PRF, dual axis encoder input and achieves outstanding signal quality.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window