where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
603 views
Technical Discussions
Arman
Engineering,
Turkey, Joined Oct 2014, 42

Arman

Engineering,
Turkey,
Joined Oct 2014
42
16:20 Jun-22-2016
Maximum Apmlitude Sizing in PA

Gentlemen,

May I know your idea about applicability and accuracy of "Maximum Amplitude sizing" for height sizing of defects detected in an un-focused phased array data (inspection beyond the near zone) , when I compared sizing accuracy with ToFD I realized that using 6dB is not accurate enough, all defects were oversized.

Also Could you please introduce a reference about "Maximum Amplitude sizing", I'm interested to read about it.

Kind Regards,
Arman

 
 Reply 
 
Andrew Cunningham
NDT Inspector
Canada, Joined Jun 2008, 238

Andrew Cunningham

NDT Inspector
Canada,
Joined Jun 2008
238
22:25 Jun-22-2016
Re: Maximum Apmlitude Sizing in PA
In Reply to Arman at 16:20 Jun-22-2016 (Opening).

The Max Amp cross sectional sizing method stands head and shoulders against any other sizing methods if you have been taught properly and have practiced, practiced and practiced. Max Amp is not so good for length, it is very dependent on the type of discontinuity you are trying to size. Multi-faceted reflectors (slag, crack and porosity) can be sized easily, but fusion type can be grossly under sized. So defect characterization is a part of Max Amp training.

 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Customized Probes and Transducers

With a strong development department and our own piezocomposite production, we accompany you from th
...
e first product idea to serial production. Our scientists are continuously researching new methods in the field of ultrasonic measurement technology. The progress achieved enables us to offer you optimal solutions.
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Research and Application Development For NDT

Acuren’s Research and Application Development specializes in the development of advanced ultraso
...
nic inspection techniques and systems for challenging inspection applications, with an emphasis on practical solutions which are field deployable. Services include manual and automated ultrasonic inspection system development, inspection technique optimization using laboratory scale studies and ultrasonic modeling (CIVA, BeamTool), preparing technical justification for technique evaluation and qualification (Probability of Detection and sizing accuracy studies), inspection/calibration/analysis procedure preparation to support field deployment of custom techniques, and development of custom imaging algorithms to support challenging inspection applications.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window