where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

1242 views
Technical Discussions
umeshkumar
umeshkumar
07:15 Jul-08-2016
for thickness 03 mm ,lamination check

Dear Experts,

can you suggest what will be the frequency(T/R-Probe) of probe use for 3 mm wall thickness ,check for lamination.

 
 Reply 
 
dhiliban
Other, QA/QC engineer
L&T HCP, India, Joined May 2016, 16

dhiliban

Other, QA/QC engineer
L&T HCP,
India,
Joined May 2016
16
10:00 Jul-08-2016
Re: for thickness 03 mm ,lamination check
In Reply to umeshkumar at 07:15 Jul-08-2016 (Opening).

Use:-4-5 MHZ probes


The sensitivity of the probe is directly proprtional to its frequency
and The depth of penetration is inversely proportional to frequency

So if you use a probe with higher frequency you will have better sensitivity,since your thickness is less,depth of penetration wont be a problem.


With regards,
Dhiliban.

 
 Reply 
 
massimo carminati
Consultant, AUT specialist
IMG Ultrasuoni Srl, Italy, Joined Apr 2007, 691

massimo carminati

Consultant, AUT specialist
IMG Ultrasuoni Srl,
Italy,
Joined Apr 2007
691
07:07 Jul-10-2016
Re: for thickness 03 mm ,lamination check
In Reply to umeshkumar at 07:15 Jul-08-2016 (Opening).

I would use a 10 MHz short focus dual probe. If you don't know where to afford it, feel free to contact me directly

 
 Reply 
 
ismail
NDT Inspector, TOFD and PAUT Specialist
Turkey, Joined Oct 2008, 27

ismail

NDT Inspector, TOFD and PAUT Specialist
Turkey,
Joined Oct 2008
27
10:27 Jul-10-2016
Re: for thickness 03 mm ,lamination check
In Reply to umeshkumar at 07:15 Jul-08-2016 (Opening).

I recommend to 15 MHz Delay line probe
Ismail

 
 Reply 
 
Kevin Humphreys
Kevin Humphreys
11:19 Jul-11-2016
Re: for thickness 03 mm ,lamination check
In Reply to umeshkumar at 07:15 Jul-08-2016 (Opening).

A dual 10 MHz should suffice

 
 Reply 
 
Darren Quinn
Darren Quinn
06:30 Jul-14-2016
Re: for thickness 03 mm ,lamination check
In Reply to umeshkumar at 07:15 Jul-08-2016 (Opening).

I am going with 10 MHZ here 6mm diameter short focus :)

 
 Reply 
 

Product Spotlight

NDT Master Lecturer

In the program both university professors and practitioners will give lectures, which guarantees the
...
oretical depth and practical inside. Academic Director: Prof. Dr. Christian Boller
The following lecturers are not complete: Prof. Tadeusz Stepinski, Prof. Wieslaw Staszewski, Prof. Frank Walther, Prof. Giovanni Bruno, Prof. Gerd Dobmann, Prof. Philippe Guy
>

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window