where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1918 views
Articles & News
Hebri
Teacher, NDT inspection
Aïn Temouchent university, Oran, Algeria, Joined Mar 2013, 4

Hebri

Teacher, NDT inspection
Aïn Temouchent university, Oran,
Algeria,
Joined Mar 2013
4
12:26 Oct-02-2016
Acoustic Emission Source Identification in Pipes Using Finite Element Analysis
Overall

Hello,
I find this work interesting. In this work can we say that we are measuring the lamb wave?

 
 Reply 
 
P V SASTRY
R & D, NDT tecniques metallurgy
TAKEN VRS FROM THE POSITION OF SR. DEPUTY GENERAL MANAGER BHEL CORPORATE R&D, India, Joined Jan 2003, 195

P V SASTRY

R & D, NDT tecniques metallurgy
TAKEN VRS FROM THE POSITION OF SR. DEPUTY GENERAL MANAGER BHEL CORPORATE R&D,
India,
Joined Jan 2003
195
02:27 Oct-03-2016
Re: Acoustic Emission Source Identification in Pipes Using Finite Element Analysis
In Reply to Hebri at 12:26 Oct-02-2016 (Opening).


Dear Sir,

The classic definition of Acoustic Emission (AE) refers to the generation of transient elastic waves in the form of stress waves.

These stress waves can be originated from deep in the components (other than the pipes) having considerable thicknesses and are propagated in all directions. Eventually they reach the surface and can travel several meters and are picked up by the sensors.

When they reach the surface and propagate they can certainly be treated as Lamb waves but not very sure before they reach the surface from several centimeters from inside the component.

Best wishes

P V SASTRY

 
 Reply 
 
Hebri
Teacher, NDT inspection
Aïn Temouchent university, Oran, Algeria, Joined Mar 2013, 4

Hebri

Teacher, NDT inspection
Aïn Temouchent university, Oran,
Algeria,
Joined Mar 2013
4
13:57 Oct-03-2016
Re: Acoustic Emission Source Identification in Pipes Using Finite Element Analysis
In Reply to P V SASTRY at 02:27 Oct-03-2016 .

Dear Sir,
Thank you for your fast response. I have other questions about this article.
- Why the force is spread over a surface area, and in which direction the force is applied?
- can we do that with a concentrated force?
- If we applied the force not perpendicular to the surface, I mean with an angle, I think we will deal with a lamb wave?

thank you again

 
 Reply 
 

Product Spotlight

Varex Imaging Large Field of View (FOV) Digital Detector Arrays (DDAs)

A larger FOV DDA can reduce the space and volume of the X-ray inspection system on the factory floor
...
, enable faster scanning times, better throughput and better resolution images at a lower dose. Customers can also save time and money. With these benefits in mind, Varex Imaging has designed a family of large FOV detectors (4343HE, XRD 1611, 4343DX-I, 4343CT) for our industrial imaging customers.
>

Magnetic X-Ray Pipeline Crawler 6''-60''

Suitable to work in 6''-60''diameter with speed of up to 18m/min, Max. moving diatance 5 kilometer
...
s and provide the efficient inspection of the pipeline.
>

FMC/TFM

Next generation for Phased Array UT is here now with FMC/TFM! Have higher resolution imaging, impr
...
oved signal to noise ratio, characterize, size and analyze defects better with access to several wave mode views and save raw FMC data for higher quality analysis.  Some of the benefits are:
  • Beautiful Image! Easier to understand what you're looking at
  • Completely focused in entire image or volume
  • Much easier to define setups before inspection
  • Easier to decipher geometry echoes from real defects
  • Oriented defects (e.g. cracks) are imaged better
  • See image from different wave modes from one FMC inspection
  • FMC data can be reprocessed/analyzed without going back to the field
>

SITEX CPSERIES

Teledyne ICM’s CPSERIES has been designed with a view to revolutionizing the handling and perfor
...
mances of portable X-Ray sets. Despite having managed to halve the weight of similar portable X-Ray generators available on the market (while continuing to provide the same power output), the SITEX CPSERIES generators feature a shutter, a laser pointer, a beryllium window, an aluminum filter and two integrated diaphragms (customized sizes are available upon request). Without compromising the robustness and reliability for which ICM products are renowned, the small size and light weight of the SITEX CPSERIES will radically change the way that you perform your RT inspections. And you will see a positive impact in terms of both quality and return on investment (ROI).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window