where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1818 views
Articles & News
Hebri
Teacher, NDT inspection
Aïn Temouchent university, Oran, Algeria, Joined Mar 2013, 4

Hebri

Teacher, NDT inspection
Aïn Temouchent university, Oran,
Algeria,
Joined Mar 2013
4
12:26 Oct-02-2016
Acoustic Emission Source Identification in Pipes Using Finite Element Analysis
Overall

Hello,
I find this work interesting. In this work can we say that we are measuring the lamb wave?

 
 Reply 
 
P V SASTRY
R & D, NDT tecniques metallurgy
TAKEN VRS FROM THE POSITION OF SR. DEPUTY GENERAL MANAGER BHEL CORPORATE R&D, India, Joined Jan 2003, 195

P V SASTRY

R & D, NDT tecniques metallurgy
TAKEN VRS FROM THE POSITION OF SR. DEPUTY GENERAL MANAGER BHEL CORPORATE R&D,
India,
Joined Jan 2003
195
02:27 Oct-03-2016
Re: Acoustic Emission Source Identification in Pipes Using Finite Element Analysis
In Reply to Hebri at 12:26 Oct-02-2016 (Opening).


Dear Sir,

The classic definition of Acoustic Emission (AE) refers to the generation of transient elastic waves in the form of stress waves.

These stress waves can be originated from deep in the components (other than the pipes) having considerable thicknesses and are propagated in all directions. Eventually they reach the surface and can travel several meters and are picked up by the sensors.

When they reach the surface and propagate they can certainly be treated as Lamb waves but not very sure before they reach the surface from several centimeters from inside the component.

Best wishes

P V SASTRY

 
 Reply 
 
Hebri
Teacher, NDT inspection
Aïn Temouchent university, Oran, Algeria, Joined Mar 2013, 4

Hebri

Teacher, NDT inspection
Aïn Temouchent university, Oran,
Algeria,
Joined Mar 2013
4
13:57 Oct-03-2016
Re: Acoustic Emission Source Identification in Pipes Using Finite Element Analysis
In Reply to P V SASTRY at 02:27 Oct-03-2016 .

Dear Sir,
Thank you for your fast response. I have other questions about this article.
- Why the force is spread over a surface area, and in which direction the force is applied?
- can we do that with a concentrated force?
- If we applied the force not perpendicular to the surface, I mean with an angle, I think we will deal with a lamb wave?

thank you again

 
 Reply 
 

Product Spotlight

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

iProbe - USB Phased Array Probe

Turn your PC, Laptop or Tablet into a powerful 32:64 Phased Array system with our USB powered Phas
...
ed Array iProbe and inspection software package. Perform affordable weld inspection and corrosion mapping inspections with this powerful but small system. The probe has a 100V pulser, 8K PRF, dual axis encoder input and achieves outstanding signal quality.
>

NOVO Armor 15 & NOVO Armor 22

The Armor Kit Contains the NOVO Armor, which provides additional mechanical protection to the NOVO 1
...
5WN & NOVO 22WN Detectors, the Armor Stand and a traveling soft cover. - Newest shock absorbent technology case - Water resistant design - Supports wired & wireless communication - Multiple positioning options - Tripod connection using the Built-in 1/4” threads - Simple Detector battery replacement
>

Semi-Automated Phased Array Immersion System for Small Composite Parts

Turn-key semi-automated system as an improved and affordable solution for inspection of small comp
...
osite parts. Includes support table, immersion tank, scanner, PA instrument, PC, Analysis software, database, wedge management and other options.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window