where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
594 views
Technical Discussions
John Wagner
Engineering
Tenneco Automotive, USA, Joined Apr 2004, 3

John Wagner

Engineering
Tenneco Automotive,
USA,
Joined Apr 2004
3
04:46 May-12-2004
Ultrasonic Testing of Adhesive Bonds

The product is an automotive suspension component consisting of a torus of rubber molded between and bonded to two
coaxial steel cylinders. Attempts to test the bond via ultrasonics required submersion of the product in water. The result, even if successful, is an unsaleable product. What is needed is a technique for evaluating the bond on prototypes developed to complete FMEA testing prior to full scale production. Any suggestions for an application generally applicable to a range of products of this type would be appreciated.


 
 Reply 
 
John O'Brien
Consultant, -
Chevron ETC , USA, Joined Jan 2000, 280

John O'Brien

Consultant, -
Chevron ETC ,
USA,
Joined Jan 2000
280
03:39 May-12-2004
Re: Ultrasonic Testing of Adhesive Bonds
Try calling NDT Automation Division of Physical Acoustics in Princeton New Jersey. Their T-SCOUT System may do the job.


 
 Reply 
 
Richard Kazares
Richard Kazares
06:00 May-13-2004
Re: Ultrasonic Testing of Adhesive Bonds
As you probably know, there are more ways than submersion in water to introduce an ultrasonic coupling techniques.

We have successfully used squirters, bubblers (weepers) - which use minute amounts of water only on the surface, and other elastomer couplants - which are typically used in wheel probes - but can also be fixed - WITHOUT any water couplant (or other gel-like materials) used.

Depending on your inspection requirements (I'm assuming you are looking for the bond between metal and elastomer - but you could possibly be looking at the elastomer consistency itself) there are other factors that might come into play.

I'd be happy to answer you directly - and in more detail, just send an e-mail.

----------- Start Original Message -----------
: The product is an automotive suspension component consisting of a torus of rubber molded between and bonded to two
: coaxial steel cylinders. Attempts to test the bond via ultrasonics required submersion of the product in water. The result, even if successful, is an unsaleable product. What is needed is a technique for evaluating the bond on prototypes developed to complete FMEA testing prior to full scale production. Any suggestions for an application generally applicable to a range of products of this type would be appreciated.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

ISONIC 3510

Very Powerful Superior Performance Extremely Portable Smart Phased Array Ultrasonic Flaw Detector an
...
d Recorder with 2 Conventional UT and TOFD Channels uniquely combines PA, single- and multi-channel conventional UT, and TOFD modalities providing 100% raw data recording and imaging. Suitable for all kinds of every-day ultrasonic inspections
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

Panther

M2M PANTHER is a phased-array equipment designed for both desktop and industrial applications, offer
...
ing unparalleled performance in a compact unit. It combines the speed required for industrial integrated Phased-Array Ultrasound (PAUT) solutions, with the most complete set of total focusing method (TFM) imaging techniques, making it the ultimate tool for R&D and procedure qualification.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window