where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

10015 views
Technical Discussions
omar a . rugebani
NDT Inspector
Libya, Joined Jul 2002, 1

omar a . rugebani

NDT Inspector
Libya,
Joined Jul 2002
1
08:12 May-23-2004
Isovolt 160TL X-ray Equipment

We have mobile industerial X-ray type isovolt 160Tl with control ES 2 , the gas pressure inside the high voltage generator has gone byond the recommended level ( 2.5 bar) and we want to re-fill it , any body knows that type of gas used with this type of equipment


 
 Reply 
 
Ulrich Mletzko
R & D, Retired
Germany, Joined Nov 1998, 89

Ulrich Mletzko

R & D, Retired
Germany,
Joined Nov 1998
89
02:33 May-25-2004
Re: Isovolt 160TL X-ray Equipment
----------- Start Original Message -----------
: We have mobile industerial X-ray type isovolt 160Tl with control ES 2 , the gas pressure inside the high voltage generator has gone byond the recommended level ( 2.5 bar) and we want to re-fill it , any body knows that type of gas used with this type of equipment
------------ End Original Message ------------

Just ask the manufacturer. The brand name ISOVOLT belongs to Seifert (Ahrensburg near Hamburg, Germany). The owners have changed, therefore ask your local representative of General Electrics (resp. Krautkramer resp. Agfa).

Regards
Uli Mletzko
MPA, University of Stuttgart, Germany




 
 Reply 
 
Troy Foster
Engineering, X-ray Inspection Systems
Willick Engineering Company, USA, Joined Feb 2000, 6

Troy Foster

Engineering, X-ray Inspection Systems
Willick Engineering Company,
USA,
Joined Feb 2000
6
02:18 May-25-2004
Re: Isovolt 160TL X-ray Equipment
----------- Start Original Message -----------
: We have mobile industerial X-ray type isovolt 160Tl with control ES 2 , the gas pressure inside the high voltage generator has gone byond the recommended level ( 2.5 bar) and we want to re-fill it , any body knows that type of gas used with this type of equipment
------------ End Original Message ------------

Sulfer Hexafluoride commonly known as SF6

Troy Foster
troy@willick.com


 
 Reply 
 
Ilya Galeev
Engineering
Industry-Service JSC, Russia, Joined Jul 2004, 1

Ilya Galeev

Engineering
Industry-Service JSC,
Russia,
Joined Jul 2004
1
06:26 Jul-06-2004
Re: Isovolt 160TL X-ray Equipment
voltage generator has gone byond the recommended level ( 2.5 bar) and we want to re-fill it , any body knows that type of gas used with this type of equipment
------------ End Original Message ------------

Hello!
If you did not reach Seifert yet are not afraid to get an advice from their competitor...
So. The unit looks being old and of "low pressure" technology, so you can add some SF6 yourself. This gas is quite common as it used also in electric power generation, etc. Usually it goes in big cylinders, so you will need 1) pressure regulator 2) proper adaptor valve.
To check what adaptor do you need - open the small cover on generator tank? usually near manometer, and if there is a car tire nipple - that is! If the nipple is of different type, close it and forget about repairing yourself.
I mentioned "low pressure" (2,5 to 3,5 bar) because tanks with higher pressure require a vacuum pump te refill. In your case you must only add some SF6 to move the pressure gauge needle just above the green mark, and even in case some air will come inside there would be no harm to your equipment.
I have done this several times on Philips COP generators and Philips/Toshiba tanksets with success.
But modern sets with high pressure tanks have smaller insulation gaps and I do not recommend to refill yourself. Usually it is prohibited at all as any air, dust or moisture coming inside will degrade the dielectric strength of the insulation, even dust particle can explode inside making the unit inoperatible (permanent flash-over above certain kV).

In any case - do not hesitate to chase me also by E-mail,
Yours Aye,

ILYA



 
 Reply 
 

Product Spotlight

IRIS 9000Plus - Introducing the next generation of heat exchanger inspection.

Representing the seventh generation of the IRIS system, the IRIS 9000 Plus has nearly 200 years of c
...
ombined field inspection experience incorporated in its design. This experience combined with a strong commitment to quality and a history of innovation has made Iris Inspection Services® the undisputed leader in IRIS technology.
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

Customized Probes and Transducers

With a strong development department and our own piezocomposite production, we accompany you from th
...
e first product idea to serial production. Our scientists are continuously researching new methods in the field of ultrasonic measurement technology. The progress achieved enables us to offer you optimal solutions.
>

PAUT Probes

Typical Phased Array probes have frequencies between 1MHz and 20MHz and the number of wafers is 10
...
to 128. M2 Electronics offers customers conventionally ultrasound probes and the ability to provide high-precision Phased Array Ultrasound Probes of up to 256 wafers. We can also customize the probe for our customers to meet the specific application requirements of the user.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window