where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

DASEL SISTEMAS
Our Phased Array equipments, based on SITAU Technology, are among the PAS highest performance in the market.
636 views
Technical Discussions
kamran azari
kamran azari
03:39 Aug-22-2004
Detection of inclusions in sheet steels by magnetic particle inspection.

Dear Sir/Madam,
I am a M.Sc student in Materials science and technology. I,m very interested in the "detection of inclusions in cold rolled sheet steels by magnetic particle inspection". I need some information about the "current intensity and location (depth) and size of the inclusion which will be detected". Some articles have information about only two of them. Would you please send me some information relative to this subject.

Sincerely,
Kamran Azari


80, mousavi court
yahyakhan alley, chaharbagh bala ave.
Isfahan, 81736 67731
IRAN.


 
 Reply 
 
Joe Buckley
Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT, United Kingdom, Joined Oct 1999, 523

Joe Buckley

Consultant, ASNT L-III, Honorary Secretary of BINDT
Level X NDT, BINDT,
United Kingdom,
Joined Oct 1999
523
03:02 Aug-22-2004
Re: Detection of inclusions in sheet steels by magnetic particle inspection.
In rolled steel sheet Inclusions will be transformed by the rolling process into delaminations, parallel to the surface. MPI is unlikely to be an effective method to detect them, since in this orientation they will cause minimal disturbance to the flux lines. UT is likely to be a more effective method

Rgds

Joe

----------- Start Original Message -----------
: Dear Sir/Madam,
: I am a M.Sc student in Materials science and technology. I,m very interested in the "detection of inclusions in cold rolled sheet steels by magnetic particle inspection". I need some information about the "current intensity and location (depth) and size of the inclusion which will be detected". Some articles have information about only two of them. Would you please send me some information relative to this subject.
: Sincerely,
: Kamran Azari
:
: 80, mousavi court
: yahyakhan alley, chaharbagh bala ave.
: Isfahan, 81736 67731
: IRAN.
------------ End Original Message ------------




 
 Reply 
 
Sandro
Sandro
09:21 Aug-23-2004
Re: Detection of inclusions in sheet steels by magnetic particle inspection.
----------- Start Original Message -----------
: Dear Sir/Madam,
: I am a M.Sc student in Materials science and technology. I,m very interested in the "detection of inclusions in cold rolled sheet steels by magnetic particle inspection". I need some information about the "current intensity and location (depth) and size of the inclusion which will be detected". Some articles have information about only two of them. Would you please send me some information relative to this subject.
: Sincerely,
: Kamran Azari
:
: 80, mousavi court
: yahyakhan alley, chaharbagh bala ave.
: Isfahan, 81736 67731
: IRAN.
------------ End Original Message ------------


Good morning Kamran Azari,
You have to know ASTM E-709 "Standard Guide for Magnetic Particle Examination"

Best regards,

Sandro
BOLIVIA




 
 Reply 
 

Product Spotlight

GEKKO - Portable Phased Array Testing with TFM in Real-Time

The portable phased array testing system GEKKO provides 64 parallel test channels. On creating testi
...
ng parameters the operator is assisted by the CIVA software. Due to its modular set-up the GEKKO instrument is suitable for operators of all skill levels.
>

High-end Ultrasonic Flaw Detector with 32:128PR PAUT and 2-ch TOFD: SyncScan 2

SIUI’s newly launched SyncScan 2, is a high-end ultrasonic flaw detector with 32:128PR PAUT and
...
2-ch TOFD, which can maximize your efficiency for PA and TOFD. ● Support PA/TOFD/UT ● 32-ch PA is more suitable for inspection on extra-thick wall and high-attenuation material. ● 32-ch PA and 2-ch TOFD work simultaneously. ● Support PR mode for corrosion inspection.
>

Panther

M2M PANTHER is a phased-array equipment designed for both desktop and industrial applications, offer
...
ing unparalleled performance in a compact unit. It combines the speed required for industrial integrated Phased-Array Ultrasound (PAUT) solutions, with the most complete set of total focusing method (TFM) imaging techniques, making it the ultimate tool for R&D and procedure qualification.
>

OmniScan™ X3 flaw detector

The OmniScan X3 flaw detector is a complete phased array toolbox. Powerful tools, like total focus
...
ing method (TFM) images and advanced visualization capabilities, enable you to complete your inspection with greater confidence.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window