where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1630 views
Technical Discussions
Micha
Micha
04:55 Sep-07-2004
SAW and ERW pipes - standards

does anybody know of specific standards for UT of SAW and ERW pipes?
specificaly i am interested in the standards for inspection of the weld seam.


 
 Reply 
 
Ed T.
Ed T.
05:21 Sep-08-2004
Re: SAW and ERW pipes - standards
----------- Start Original Message -----------
: does anybody know of specific standards for UT of SAW and ERW pipes?
: specificaly i am interested in the standards for inspection of the weld seam.
------------ End Original Message ------------

Look in ASME Section V, Article 4 or 5. The basic calibration blocks for UT are based on the base material not the welding process.
However, the UT operator should be familiar with the welding process in order to determine what type of indications to excpect.


 
 Reply 
 
ajay singh
ajay singh
05:05 Feb-16-2005
Re: SAW and ERW pipes - standards
Dear sir,
we are looking for Stainless steel ERW or seam less pipe of AISI 304 or
310 grade.
outer dia 48.3 /44.5 thickness 2.6-2.7 MM length 6.1 Mt
Final destination Kolkata/Mumbai India.

Pls. offer your best price C&F destnation.Qunatity required is up to
200MT per month.
Regards,
ajay singh




 
 Reply 
 
Nikhil Arya
NDT Inspector
Surya Roshni Limited (Steel Division), India, Joined Jul 2005, 1

Nikhil Arya

NDT Inspector
Surya Roshni Limited (Steel Division),
India,
Joined Jul 2005
1
06:00 Jul-11-2005
Re: SAW and ERW pipes - standards
----------- Start Original Message -----------
: : does anybody know of specific standards for UT of SAW and ERW pipes?
: : specificaly i am interested in the standards for inspection of the weld seam.
: Look in ASME Section V, Article 4 or 5. The basic calibration blocks for UT are based on the base material not the welding process.
: However, the UT operator should be familiar with the welding process in order to determine what type of indications to excpect.
------------ End Original Message ------------

i can tell only for the ERW pipes. N10 & N5 notches at OD & ID are used and through holes at wels seam are used.


 
 Reply 
 
E Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1286

E Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1286
00:30 Jul-12-2005
Re: SAW and ERW pipes - standards
Standards for ERW and SAW pipe seam welds are similar world wide.
The North American versions are API 5L and in Canada CSA Z-245.
A Standard Practice by ASTM is also used, ASTM E-273.

Regards
Ed

----------- Start Original Message -----------
: : : does anybody know of specific standards for UT of SAW and ERW pipes?
: : : specificaly i am interested in the standards for inspection of the weld seam.
: : Look in ASME Section V, Article 4 or 5. The basic calibration blocks for UT are based on the base material not the welding process.
: : However, the UT operator should be familiar with the welding process in order to determine what type of indications to excpect.
: i can tell only for the ERW pipes. N10 & N5 notches at OD & ID are used and through holes at wels seam are used.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Sci Aps Z-Series Portable Handheld Analysers

The world’s only handheld analyzer that measures carbon content in stainless (yes even L-grades),s
...
teels, and cast irons. Also accepted for low Si analysis for sulfidic corrosion analysis, and is widely used in the power industry for Cr analysis, for flow accelerated corrosion applications.
>

TESTD-PT SYSTEM

Pulse thermography is a non-contact test method that is ideal for the characterization of thin fil
...
ms and coatings or the detection of defects. With a remarquable short test time and a high detection sensitivity, the Telops TESTD-PT is the perfect tool for non- destructive testing. With such high frame rates, it is even possible to investigate highly conductive or diffusive materials.
>

YXLON Cougar EVO

Scalable small footprint X-ray inspection systems for assembly and laboratory applications. The
...
YXLON Cougar EVO series was designed to provide the "best-in- class" inspection solutions for SMT, semiconductor, and laboratory assembly applications, while maintaining a small system footprint for maximum convenience. With optimized software and hardware, these systems produce higher quality and more consistent results than other electronics inspection systems currently on the market.
>

NEOS III

NEOS III is Logos Imagings lightest DR system. With a built-in battery and internal wireless commu
...
nication, the NEOS III is perfect for users that want to quickly assess an item.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window