where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

GRANPECT COMPANY Ltd
GRANPECT bends to the industrialization of high-tech research achievements and specializes in research and development of various X-ray radiation imag ...
1574 views
Technical Discussions
Micha
Micha
04:55 Sep-07-2004
SAW and ERW pipes - standards

does anybody know of specific standards for UT of SAW and ERW pipes?
specificaly i am interested in the standards for inspection of the weld seam.


 
 Reply 
 
Ed T.
Ed T.
05:21 Sep-08-2004
Re: SAW and ERW pipes - standards
----------- Start Original Message -----------
: does anybody know of specific standards for UT of SAW and ERW pipes?
: specificaly i am interested in the standards for inspection of the weld seam.
------------ End Original Message ------------

Look in ASME Section V, Article 4 or 5. The basic calibration blocks for UT are based on the base material not the welding process.
However, the UT operator should be familiar with the welding process in order to determine what type of indications to excpect.


 
 Reply 
 
ajay singh
ajay singh
05:05 Feb-16-2005
Re: SAW and ERW pipes - standards
Dear sir,
we are looking for Stainless steel ERW or seam less pipe of AISI 304 or
310 grade.
outer dia 48.3 /44.5 thickness 2.6-2.7 MM length 6.1 Mt
Final destination Kolkata/Mumbai India.

Pls. offer your best price C&F destnation.Qunatity required is up to
200MT per month.
Regards,
ajay singh




 
 Reply 
 
Nikhil Arya
NDT Inspector
Surya Roshni Limited (Steel Division), India, Joined Jul 2005, 1

Nikhil Arya

NDT Inspector
Surya Roshni Limited (Steel Division),
India,
Joined Jul 2005
1
06:00 Jul-11-2005
Re: SAW and ERW pipes - standards
----------- Start Original Message -----------
: : does anybody know of specific standards for UT of SAW and ERW pipes?
: : specificaly i am interested in the standards for inspection of the weld seam.
: Look in ASME Section V, Article 4 or 5. The basic calibration blocks for UT are based on the base material not the welding process.
: However, the UT operator should be familiar with the welding process in order to determine what type of indications to excpect.
------------ End Original Message ------------

i can tell only for the ERW pipes. N10 & N5 notches at OD & ID are used and through holes at wels seam are used.


 
 Reply 
 
E Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1282

E Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1282
00:30 Jul-12-2005
Re: SAW and ERW pipes - standards
Standards for ERW and SAW pipe seam welds are similar world wide.
The North American versions are API 5L and in Canada CSA Z-245.
A Standard Practice by ASTM is also used, ASTM E-273.

Regards
Ed

----------- Start Original Message -----------
: : : does anybody know of specific standards for UT of SAW and ERW pipes?
: : : specificaly i am interested in the standards for inspection of the weld seam.
: : Look in ASME Section V, Article 4 or 5. The basic calibration blocks for UT are based on the base material not the welding process.
: : However, the UT operator should be familiar with the welding process in order to determine what type of indications to excpect.
: i can tell only for the ERW pipes. N10 & N5 notches at OD & ID are used and through holes at wels seam are used.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Ultrasonic Testing Immersion Tanks with Unmatched Scanning Features

TecScan’s non-destructive testing Ultrasonic Immersion Tanks & scanners are designed for high pe
...
rformance and demanding NDT testing applications. Our Scan3D™ line of High Precision Immersion Tanks are specifically designed for automated ultrasonic testing of complex composites parts used in aerospace and industrial applications.
>

ISAFE3 Intrinsically Safe Sensor System

ISAFE3 intrinsically safe sensor system of Vallen Systeme is especially targeted at the petrochemica
...
l - as well as oil and gas transportation industry. The sensor system is designed for permanent monitoring or periodic inspection tasks. Sensors are available for different AE-frequency ranges optimized for corrosion and fatigue crack detection and other applications. The ISAFE 3 sensor system consists of an AE-sensor (model ISAS3) certified according to ATEX/IEC for installation in zone 0, gas group IIC, IP68, 20 to +60 °C, and a signal isolator (model SISO3) certified for installation in zone 2. An ISAS3 sensor can be mounted in atmosphere or submerged, e.g. in water or crude oil. It is supported by mounting tools for temporary (magnets) or permanent (welded) installation. ISAFE3 supports automatic sensor coupling test and can be used with any AE signal processor supporting 28V supply at 90 mA peak, e.g. Vallen Systeme ASIP-2/A.
>

HARDNESS TESTER TKM-459CE combi

TKM-459CE combi applies 2 methods of hardness control: UCI and Leeb. It provides high-accuracy tes
...
ting of metals and alloys as well as items of different sizes and configurations, their hardened layers and galvanic coatings. Device represents results in HB, HRC, HV and others. Shock-, dust- and water-proof housing with intuitive software make this gauge easy to use in all working conditions.
>

HD-CR 35 NDT Computed Radiography System

Portable high-resolution CR scanner for all radiography applications - weld testing, profile images
...
and aerospace. No matter what type of radiographic testing you are performing, the unique TreFoc Technology of the HD-CR 35 NDT imaging plate scanner always guarantees the highest image quality.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window