where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -
1570 views
Technical Discussions
Micha
Micha
04:55 Sep-07-2004
SAW and ERW pipes - standards

does anybody know of specific standards for UT of SAW and ERW pipes?
specificaly i am interested in the standards for inspection of the weld seam.


 
 Reply 
 
Ed T.
Ed T.
05:21 Sep-08-2004
Re: SAW and ERW pipes - standards
----------- Start Original Message -----------
: does anybody know of specific standards for UT of SAW and ERW pipes?
: specificaly i am interested in the standards for inspection of the weld seam.
------------ End Original Message ------------

Look in ASME Section V, Article 4 or 5. The basic calibration blocks for UT are based on the base material not the welding process.
However, the UT operator should be familiar with the welding process in order to determine what type of indications to excpect.


 
 Reply 
 
ajay singh
ajay singh
05:05 Feb-16-2005
Re: SAW and ERW pipes - standards
Dear sir,
we are looking for Stainless steel ERW or seam less pipe of AISI 304 or
310 grade.
outer dia 48.3 /44.5 thickness 2.6-2.7 MM length 6.1 Mt
Final destination Kolkata/Mumbai India.

Pls. offer your best price C&F destnation.Qunatity required is up to
200MT per month.
Regards,
ajay singh




 
 Reply 
 
Nikhil Arya
NDT Inspector
Surya Roshni Limited (Steel Division), India, Joined Jul 2005, 1

Nikhil Arya

NDT Inspector
Surya Roshni Limited (Steel Division),
India,
Joined Jul 2005
1
06:00 Jul-11-2005
Re: SAW and ERW pipes - standards
----------- Start Original Message -----------
: : does anybody know of specific standards for UT of SAW and ERW pipes?
: : specificaly i am interested in the standards for inspection of the weld seam.
: Look in ASME Section V, Article 4 or 5. The basic calibration blocks for UT are based on the base material not the welding process.
: However, the UT operator should be familiar with the welding process in order to determine what type of indications to excpect.
------------ End Original Message ------------

i can tell only for the ERW pipes. N10 & N5 notches at OD & ID are used and through holes at wels seam are used.


 
 Reply 
 
E Ginzel
R & D, -
Materials Research Institute, Canada, Joined Nov 1998, 1282

E Ginzel

R & D, -
Materials Research Institute,
Canada,
Joined Nov 1998
1282
00:30 Jul-12-2005
Re: SAW and ERW pipes - standards
Standards for ERW and SAW pipe seam welds are similar world wide.
The North American versions are API 5L and in Canada CSA Z-245.
A Standard Practice by ASTM is also used, ASTM E-273.

Regards
Ed

----------- Start Original Message -----------
: : : does anybody know of specific standards for UT of SAW and ERW pipes?
: : : specificaly i am interested in the standards for inspection of the weld seam.
: : Look in ASME Section V, Article 4 or 5. The basic calibration blocks for UT are based on the base material not the welding process.
: : However, the UT operator should be familiar with the welding process in order to determine what type of indications to excpect.
: i can tell only for the ERW pipes. N10 & N5 notches at OD & ID are used and through holes at wels seam are used.
------------ End Original Message ------------




 
 Reply 
 

Product Spotlight

Varex Imaging Large Field of View (FOV) Digital Detector Arrays (DDAs)

A larger FOV DDA can reduce the space and volume of the X-ray inspection system on the factory floor
...
, enable faster scanning times, better throughput and better resolution images at a lower dose. Customers can also save time and money. With these benefits in mind, Varex Imaging has designed a family of large FOV detectors (4343HE, XRD 1611, 4343DX-I, 4343CT) for our industrial imaging customers.
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

UCI Hardness Tester NOVOTEST T-U2

UCI hardness tester NOVOTEST T-U2 is is used for non-destructive hardness testing of: metals and
...
alloys by scales of hardness: Rockwell (HRC), Brinell (HB), Vickers (HV); non-ferrous metals, alloys of iron etc., and using five additional scales for calibration; with tensile strength (Rm) scale determines the tensile strength of carbon steel pearlitic products by automatic recalculation from Brinell (HB) hardness scale.
>

Immersion systems

ScanMaster ultrasonic immersion systems are designed for high throughput, multi shift operation in a
...
n industrial or lab environment. These fully integrated systems provide various scanning configurations and incorporate conventional and phased arrays technologies to support diverse applications, such as inspection of disks, bars, shafts, billets and plates. All of ScanMaster immersion systems are built from high accuracy scanning frames allowing for scanning of complex parts and include a multi-channel ultrasonic instrument with exceptional performance. The systems are approved by all major manufacturers for C-scan inspection of jet engine forged discs. Together with a comprehensive set of software modules these flexible series of systems provide the customer with the best price performance solutions.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window