where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

773 views
Technical Discussions
Leon
Engineering
Welding Technology Instirute of Australia, Australia, Joined Sep 2004, 1

Leon

Engineering
Welding Technology Instirute of Australia,
Australia,
Joined Sep 2004
1
03:49 Sep-10-2004
testing of austenitic spot welds

What is the best method of non destructive testing of spot welds in austenitic stainless steels and what is the current state of the art? Thicknesses of base materials vary from 1.6 mm to 6 mm in mainly grade 304 and 304L. I have seen sme articles on high frequency UT probes for testing of automotive spot welds in carbon steels but nothing on austenitics.
Is any work being done on phased array testing of spot welds?


 
 Reply 
 
S.V.Swamy
Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex , India, Joined Feb 2001, 787

S.V.Swamy

Engineering, - Material Testing Inspection & Quality Control
Retired from Nuclear Fuel Complex ,
India,
Joined Feb 2001
787
06:08 Sep-12-2004
Re: testing of austenitic spot welds
Dear Leon,

Ultrasonic testing of austenitic ss welds is a little more complicated than carbon steels. What is the button thickness? And what are the defects that you are looking for in addition to incomplete fusion? What is the defect library built up through sectioning?

Pl. feel free to contact me for further discussion. We have done good work on testing of spot welds on thin sections of zirconium alloy tubes and have published our work too.

Best wishes.

Swamy

----------- Start Original Message -----------
: What is the best method of non destructive testing of spot welds in austenitic stainless steels and what is the current state of the art? Thicknesses of base materials vary from 1.6 mm to 6 mm in mainly grade 304 and 304L. I have seen sme articles on high frequency UT probes for testing of automotive spot welds in carbon steels but nothing on austenitics.
: Is any work being done on phased array testing of spot welds?
------------ End Original Message ------------




 
 Reply 
 
Rolf D.
Director,
NDT.net, Germany, Joined Nov 1998, 617

Rolf D.

Director,
NDT.net,
Germany,
Joined Nov 1998
617
09:12 Sep-13-2004
Re: testing of austenitic spot welds
----------- Start Original Message -----------
: What is the best method of non destructive testing of spot welds in austenitic stainless steels and what is the current state of the art? Thicknesses of base materials vary from 1.6 mm to 6 mm in mainly grade 304 and 304L. I have seen sme articles on high frequency UT probes for testing of automotive spot welds in carbon steels but nothing on austenitics.
: Is any work being done on phased array testing of spot welds?
------------ End Original Message ------------

I have heard during the WCNDT Montreal that people recently
evaluating phased array technique of spot welds.

There was also held the lecture:
NONDESTRUCTIVE TESTING ACTIVITIES, NEEDS, AND TRENDS IN THE AUTOMOTIVE INDUSTRY
G. Mozurkewich
Ford Motor Company, Research and Advanced Engineering, Dearborn, Michigan, USA

In NDT.net's October issue we'll have this and all other WCNDT papers at NDT.net available.

If you need, I could send you the PDF paper already now and/or theemail address of George Mozurkewich.

Rolf Diederichs


 
 Reply 
 

Product Spotlight

Micro CT

nanoVoxel series has nano-scale resolution upto 500nm by using high voltage X-ray source (from 80-
...
300 kV) with micro/nano focal spot and highly sensitive flat panel detectors and unique Optical coupling detector.
>

FD800 Bench Top Flaw Detectors

The bench-top FD800 flaw detector range combines state-of-the-art flaw detection with advanced mater
...
ial thickness capabilities. Designed for use in the laboratory these gauges are the tool you need for all your flaw detecting needs.
>

NEW - TD Focus-ScanRX

The NEW Next Generation Advanced UT platform, TD Focus ScanRX - Also available as a card stack solut
...
ion. Key Improvements 1. Data acquisition is significantly faster than current design 2. Better aesthetic – closely aligns with HandyScan RX 3. Improved IP rating (Target IP66) 4. Ruggedized housing 5. Connectors are protected from impact and ingress 6. Integrated stand and separate retractable handle easy to keep clean) 7. Touchscreen with ruggedized display glass 8. 3-Axis encoder input
>

Eddy Current inspection : RotoETscan Rotating Head

The rotating head RotoETscan detects the presence of longitudinal surface or sub surface defects a
...
t high speed. The rotating head is often installed directly on the production line. It is generally dedicated to the control of long products such as tubes, bars and wires, made of ferrous or non-ferrous material. It can also be used for inspection of small parts (billets).
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window