where expertise comes together - since 1996 -

The Largest Open Access Portal of Nondestructive Testing (NDT)

Conference Proceedings, Articles, News, Exhibition, Forum, Network and more

where expertise comes together
- since 1996 -

198 views
Technical Discussions
Grzegorz
NDT Inspector,
Poland, Joined Feb 2012, 15

Grzegorz

NDT Inspector,
Poland,
Joined Feb 2012
15
11:52 Aug-21-2019
ASTM 2175 Requirements of penetrant inspection

Hi,
Did someone work with this standard in refer to PT.
I need information about what is subject of evaluation discontinuities or indications??
Thank in advance.

 
 Reply 
 
SUMURAY
SUMURAY
18:45 Aug-21-2019
Re: ASTM 2175 Requirements of penetrant inspection
In Reply to Grzegorz at 11:52 Aug-21-2019 (Opening).

Excuse me SIR.
are you sure of this standard is correct?
I Think is ASTM E1417 or ASTM E165.

 
 Reply 
 
Grzegorz
NDT Inspector,
Poland, Joined Feb 2012, 15

Grzegorz

NDT Inspector,
Poland,
Joined Feb 2012
15
08:00 Aug-22-2019
Re: ASTM 2175 Requirements of penetrant inspection
In Reply to SUMURAY at 18:45 Aug-21-2019 .

Sie,
You're right, these mentioned by you standards refer to PT, but both contain only parameters for carring out of test.
ASTM 2175 contains only requirements of all NDT tests among others PT.

 
 Reply 
 

Product Spotlight

Extended Range Variable Wall® Piping Calibration Blocks for Longseam Inspection

This set of two blocks has been specially designed for situations where ultrasonic examination tak
...
es place circumferentially or “around the curve” for applications such as inspection of longseam welds in piping and vessels. Jointly designed by PH Tool and Holloway NDT, the blocks feature side-drilled hole reflectors positioned within novel compound-curves, each with multiple thickness steps. The unique design results in a light and compact form factor, with the largest block weighing just over 15 lbs and spanning just 16 ¾”. Coverage is provided for nominal pipe sizes from 6” to 10” in the small block and 12” to a whopping 56” in the large block. The compound OD curves and multiple wall thicknesses actually exceed ASME requirements, providing exceptional signal response and measurement accuracy. Properly managing beam divergence off the ID and stabilizing beam skew due to probe rocking is essential to maintaining a consistent calibration when inspecting lengthwise on curved surfaces.
>

Compact NDT inspection-heads for measurements with active thermography

The compact inspection head is suitable for thermographic ndt tasks. The uncooled infrared camera
...
is specially developed for NDI-tasks and offers a thermal sensitivity until now known only from thermal imagers with cooled detector. All required components and functions are integrated into the inspection-head. You will only need an ethernet cable to connect the sensor with the evaluation system.
>

Ultrasonic Probe Recharacterization Service

NDT Systems offers a comprehensive Aftercare and Recharacterization Service for all our ultrasonic
...
probes. The Recharacterization Service is fully compliant with International ASTM E1065 Standard Guide (and other applicable standards) and offers complete documentation, traceable to the ASTM E1065 Standard. For more details or to schedule Recharacterization Services contact ndtsales@ndtsystems.com
>

MANTIS

MANTIS is a compact, powerful and affordable flaw detector (16:64PR), dedicated to field operators
...
. This portable equipment offers standard (electronic-, sector-, compound scan, conventional UT for pulse-echo, dual array and TOFD inspections), and advanced phased-array (real-time TFM -Total Focusing Method). MANTIS benefits from the same intuitive and user-friendly interface (CAPTURE) than Gekko for easier inspections.
>

Share...
We use technical and analytics cookies to ensure that we will give you the best experience of our website - More Info
Accept
top
this is debug window